Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 14 | Manualshive

Page: 14 / 39

Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 14

1

4

Installation Instructions

Chapter 3

Step 9

Attach Drip Shield to bottom of framed opening using (3)

proper

Screws (Not Provided).

See Figure 9A and 9B

. If a

100mm

wall is used a support board must be installed as shown in

Figure 9B

. Be sure not to deform Drip Shield when

installing screws.

Figure 9A

Figure 9B

Drip Shield

Screw

(

N

ot

P

rovided)

100mm

Wall

150mm

Wall

Drip plate

Drip plate

Support board

Barn Screw

Barn Screw

Step 10

Locate the Drain hole in the

Fiberglass

Orifice. This is the bottom of the

Orifice.

Set the bottom edge of the panel on the

Drip Shield

l

edge and center the panel on the opening. Then secure the

Orifice

to the wall using (16)

proper

Screws (Not

Provided).

See Figure10A and 10B.

NOTE:

t

he proper type of fixing screw has to be selected depending on the material of the wall of the installation.

Figure 10A

Figure 10B

Drain hole

Drip Shield ledge

Or

i

fi ce

Panel

Screws (Not Provided)

«
...
12
13
14
15
16
...
»

Summary of Contents for WM54F








































Reviews:

No comments