manualshive.com logo in svg

Munters WM54F, Manual For Use And Maintenance Including Assembling Instructions, Page: 33 / 39

Share
Download
Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 33

7.1 Troubleshooting

WARNING

!

High Voltage, disconnect power 

before servicing.

WARNING

!

Moving parts, disconnect power 

before servicing.

WARNING

!

Moving parts, disconnect 

power before servicing.

Troubleshooting

8

.

Fan Operating-
Insuffi cient Airfl ow

Excessive
Vibration

Excessive Noise

1. Fan control set above room

temperature

2. Blown fuse or open circuit breaker
3. Propeller blade contacting fan housing
4. Fan control defective
5. Motor defective

1. Damper door jammed
2. Guard dirty

1. Propeller blade contacting fan housing

1. Motor loose on mount
2. Propeller damaged
3. Motor or propeller shaft bent

1. Set to a lower temperature
2. Replace fuse or reset breaker
3. Realign motor in fan housing
4. Repair or replace control
5. Repair or replace motor

1. Clean damper door & fan housing
2. Clean guard

1. Sand fan housing to remove high spot

1. Tighten fasteners
2. Replace propeller
3. Repair or replace motor or propeller shaft

Fan Not Operating

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

Fan Never Turns 

Off

1. Override thermostat set incorrectly
2. Control set for continuous operation

1. Set to the correct temperature
2. Set control correctly

3

3

It is normal that the damper does not open completely. No corrective actions are needed.

Summary of Contents for WM54F








































Reviews:

No comments