manualshive.com logo in svg

Munters WM54F, Manual For Use And Maintenance Including Assembling Instructions, Page: 27 / 39

Share
Download
Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 27

2

7

All wiring should be installed in accordance with 

all n

ational

 and l

ocal electrical 

codes

. Fans used to ventilate 

livestock buildings or other rooms where continuous air movement is essential should be connected to individual 
electrical circuits, with a minimum of two circuits per room. For electrical connection requirements, refer to 
diagram on motor nameplate and to information enclosed with the Munters environmental control to be used.

Three Phase Fans

: motor overload protection should be provided for each fan. A three-pole

s

 

safety switch

 or slow 

blow motor fuses must be used. 

See Figure 25

. 

If a frequency drive (inverter) is used, confirm that motors are rated for inverter duty at the voltage used. The 

installation of line 

filters

 is recommended to reduce voltage spikes and harmonic distortion. Supplemental 

motor overload protection is also recommended.

NOTE

: A safety cut-off switch should be located adjacent to each fan.

KEY:

L1=Line 1

L2=Line 2
L3=Line 3
G=Ground

Three Phase 

Power Supply for 

Fan

L1

L2

G 

T1

T2

G 

Three Phase 

Power Out 

to Fan Motor

L3

T3

Figure 25

Three Phase - Motor Overload Protection with Disconnect

Saftey cut-off 

switch

Electrical Wiring

4

.

Summary of Contents for WM54F








































Reviews:

No comments