manualshive.com logo in svg

Munters WM54F, Manual For Use And Maintenance Including Assembling Instructions, Page: 19 / 39

Share
Download
Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 19

1

9

Installation Instructions

Chapter 3

Step 14A

Fasten each of the joints in the single outer hole using (1) Short Bolt [AA]

,  Washer [A]

 and Nut [DD], with 

the nut on the side with the tabs.  At the inner pair of holes of each joint attach (1) Cone Support Bracket 
to the inner hole using (1) Bolt [AA]

, Washer [A]

 and Nut [DD] with the bolt head on the side with the 

tabs.  

See Figure 14A.

Nut [DD]

Short Bolt [AA]

Outer holes

Nut [DD]

Short Bolt [AA]

Inner holes

Figure 14A

Step 14B

Stand the cone sections on end and curl ends around to form cone with the Cone Support Bracket on the outside 
and the tabs on the inside.  Then insert the remaining tabs into slots so the tabs are inside the cone and fasten 
final joint using (1) Short Bolt [AA]

, Washer [A]

 and Nut [DD], with the nut on the inside of the cone.  At the 

inner pair of holes attach (1) Cone Bracket to the inner hole using (1) Short Bolt [AA]

, Washer [A]

 and Nut 

[DD] with the bolt head on the outside of the cone.  

See Figure 14B.

Figure 14B

Cone Bracket

Short Bolt [AA]

Short Bolt [AA]

Nut [DD]

Nut [DD]

Cone Support Bracket

Washer [A]

Washer

 [A]

Washer [A]

Washer [A]

Summary of Contents for WM54F








































Reviews:

No comments