Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 20 | Manualshive

Page: 20 / 39

Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 20

20

Figure 15A

Step 15A

Install cone onto fan by putting the top of the cone over the top of the fan. The hole in the tab of the upper cone
section should slide down over the pin in the Main Frame assembly, then allow the rest of the cone to slide over
the rest of the orifice panel making sure the cone brackets remain on the outside of the cone.

See Figure 15A.

Frame Pin

Installation Instructions

Chapter 3

Hole in Tab of Cone Section

Step 15B

Place the end of the Cone Brackets with the single hole over the bolt holding the Cone/Strut Mounting Bracket
to the orifice and secure with Nut [DD].

See Figure 15B

. Secure the Cone to the Fan installing Medium Bolt

[BB]

and Washer [A]

through the remaining hole in the Cone Brackets and fastening with Nut [DD]. A long

screwdriver may be needed to help align the holes through the Cone Bracket, Cone, Damper Frame and
Orifice.

See Figure 15B..

Figure 15B

Nut [DD]

Medium Bolt [BB]

Nut [DD]

Washer [A]

«
...
18
19
20
21
22
...
»

Summary of Contents for WM54F








































Reviews:

No comments