manualshive.com logo in svg

Munters WM54F, Manual For Use And Maintenance Including Assembling Instructions, Page: 4 / 39

Share
Download
Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 4

4

CE Declaration of conformity

CE Declaration

1.

Munters Italy S.pA.

(complies with Subparagraph A Annex II Directive 2006/42/EC)

with registered officies in Strada Piani, 2 - 18027 Chiusavecchia (IM) - Italy

(Company Registration nr. 00081050080)

declares on its own responsability that the apparatus:

Designation

Model

Year of Manufacture

Fan designed for moving air to control temperature 
and humidity in livestock. 

WM54F

2017

conforms with the essential safety requirements stated by Apparatus Directive 2006/42/EC

and performance requirements comply with the ErP Directive 2009/125/CE,

with particular reference to the following provisions: UNI EN 953:2009, UNI EN ISO 12100:2010,

UNI EN ISO 12499:2009, UNI EN ISO 13857:2008, CEI EN 60204-1:2006 (CEI 44-5)

UNI EN ISO 5801:2009

Chiusavecchia, 5th July 2017

 

Marco Scomparin 

Legal Representative 

Summary of Contents for WM54F








































Reviews:

No comments