manualshive.com logo in svg

Munters WM54F, Manual For Use And Maintenance Including Assembling Instructions, Page: 32 / 39

Share
Download
Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 32

3

2

Provide Weather 
Shelter Over Fans

150mm

 Min.

Fan with
Discharge Cone

Snow Guards located 
per manufacturers 
recommendations

Ceiling

Figure 28

Winterizing

7

.

Fan with
Discharge 
Cone

Note:

 

Snow guards are designed to prevent sudden, dangerous snow 

and ice slides when attached to the building roof according to 

manufacturers recommendations. The supplier listing above is given 

as a reference only. 

Munters

 does not endorse any specific snow 

guard product and no performance warranty is implied.

 

Munters Product and System 

Warranties do not cover cone or fan 

damage from external sources.

IMPORTANT

!

Figure 27

In most climates, it is probable that the ventilation system will never need to operate at a total capacity 
during the colder winter months. Consequently, it is advisable to “winterize” those fans which will not 
be used in cold weather to avoid unnecessary heat loss and condensation.

To winterize, turn fan control “off”. Install the insulated closure panel over the fan intake. If you don’t 

have an insulated closure panel, a piece of rigid insulation material can be used. Remember the 
insulation panel must be removed before warmer weather returns.

NOTE:

  At least one single speed fan should be left uncovered and with power available to provide air     

     movement in the event of variable speed control difficulties.

7.1 Winterizing

7.2 Winter Weather Protection

To prevent cone or fan damage from snow or ice sliding off building roof, weather protection must be 
provided. A weather shelter may be constructed to cover the entire fan, 

See Figure 27,

 or snow guards 

may be placed on the roof, 

See Figure 28.

Summary of Contents for WM54F








































Reviews:

No comments