background image

© Munters Corporation, July 2021

26

QM1095r1

Munters Europe AB, Isafjordsgatan 1, P.O. Box 1150, SE-164 26 Kista, Sweden. Phone +46 08 626 63 00, Fax +46 8 754 56 66.

Munters Corporation 2691 Ena Drive  Lansing, MI 48917  U.S.A. Phone +1 800-227-2376, Fax +1 517-676-7078

www.munters.us

Australia

 Munters Pty Limited, Phone +61 2 6025 6422, 

Brazil

 Munters Brasil Industria e Comercio Ltda, Phone +55 41 3317 5050, 

Canada/US

 Munters

Corporation Lansing, MI Phone +1 517 676 7070, 

China

 Munters Air Treatment Equipment (Beijing) Co. Ltd, Phone +86 10 80 481 121, 

Denmark

 Munters A/S, 

Phone +45 9862 3311, 

India

 Munters India, Phone +91 20 3052 2520, 

Indonesia

 Munters, Phone +62 818 739 235, 

Italy

 Munters Italy S.p.A., Chiusavecchia, 

Phone +39 0183 52 11, 

Japan

 Munters K.K., Phone +81 3 5970 0021, 

Korea

 Munters Korea Co. Ltd., Phone +82 2 761 8701, 

Mexico

 Munters Mexico, Phone 

+52 818 262 54 00, 

Russia

 Munters AB, Phone +7 812 448 5740, 

Singapore

 Munters Pte Ltd., Phone +65 744 6828, 

South Africa and Sub-Sahara Countries 

Munters (Pty) Ltd., Phone +27 11 997 2000, 

Spain

 Munters Spain S.A., Phone +34 91 640 09 02, 

Sweden

 Munters AB, Phone +46 8 626 63 00, 

Thailand 

Munters Co. Ltd., Phone +66 2 642 2670, 

Turkey

 Munters Form Endüstri Sistemleri A.Ş, Phone +90 322 231 1338, 

USA

 Munters Corporation Lansing, MI Phone 

+1 517 676 7070, 

Vietnam

 Munters Vietnam, Phone +84 8 3825 6838, 

Export & Other countries

 Munters Italy S.p.A., Chiusavecchia Phone +39 0183 52 11

Atlas 74 Fan with Cone is developed and produced by Munters Corporation, Lansing, Michigan U.S.A. 1-800-227-2376

Summary of Contents for ATLAS 74



























Reviews: