Multi-Tech MultiFRAD 100-Series Owner'S Manual Download Page 88 | Manualshive

Page: 88 / 99

background image

88

7.3.1 Recording MultiFRAD Information

Please fill in the following information on your Multi-Tech MultiFRAD.
This will help Tech Support in answering your questions. (The same
information is requested on the Warranty Registration Card.)

Model Number: ______________________________________

Serial Number: ______________________________________

Firmware Version: ____________________________________

The model and serial numbers are on the bottom of your MultiFRAD.
The Diagnostics menu displays the PROM firmware version number.

Before calling Tech Support, please note in the space below if your
MultiFRAD is connected to a synchronous or asynchronous device on
the data port. Also note status information about your MultiFRAD,
including LED indicators, screen messages, diagnostic test results, or
problems with a specific application, etc.

_________________________________________________________________________________

_________________________________________________________________________________

_______________________________________________________________________________

________________________________________________________________________________________________________

______________________________________________________________________________________________________________

_______________________________________________________________________________________________________

___________________________________________________________________________________________________________________

_________________________________________________________________________________________________________________________

___________________________________________________________________________________________________________________

_________________________________________________________________________________________________________________________

___________________________________________________________________________________________________________________

_________________________________________________________________________________________________________________________

«
...
86
87
88
89
90
...
»

Summary of Contents for MultiFRAD 100-Series




































































































Reviews:

No comments

Related manuals for MultiFRAD 100-Series

Brand: XDS Pages: 99

Brand: GE Pages: 93

Brand: Makita Pages: 2

Brand: WAGO Pages: 2

Brand: Zenith Data Systems Pages: 64

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Brand: D-Link Pages: 31

Brand: Winext Pages: 37

Brand: red lion Pages: 5

Brand: A2B Electronics Pages: 24

Brand: ZALMAN Pages: 6

Brand: X-Micro Pages: 49

Brand: Airlink101 Pages: 13

Brand: CNC4PC Pages: 11

Brand: IMC Networks Pages: 36

Brand: KYLAND Technology Pages: 24

Brand: SilverStone Pages: 28

airPoint Nexus sB3210

Brand: SmartBridges Pages: 55

Brand: Juniper Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands