Multi-Tech MultiFRAD 100-Series Owner'S Manual Download Page 65 | Manualshive

Page: 65 / 99

background image

65

Back to Back

The Back to Back is used to test the port by connecting two MultiFRADs
together without a frame relay network in between them. Back-to-back
mode still requires the use of DSU/CSUs, but they should not be connected
over the frame relay network. The options are On and Off with a default of
Off.

Back-to-back mode is useful when two MultiFRADs are at the same location
and they are connected via DSUs for testing. Back-to-back mode can also
be used to connect two MultiFRADs over a private leased line.

Excess Burst Rate (Be)

The Excess Burst Rate (Be) defines the maximum allowable data transfer
rate the MultiFRAD can exceed the Committed Info Rate (CIR) during a time
interval. The Be is the maximum additional data rate at which the MultiFRAD
can present to the network during a time interval. The default Be is 24K.

«
...
63
64
65
66
67
...
»

Summary of Contents for MultiFRAD 100-Series




































































































Reviews:

No comments

Related manuals for MultiFRAD 100-Series

Brand: M-Audio Pages: 10

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

Brand: A-Link Pages: 6

Brand: A10 Pages: 52

Brand: Profile Pages: 6

Sentry Global Security Modem

Brand: Server Technology Pages: 22

BladeCenter Management Module

Brand: IBM Pages: 184

Brand: Macsense Pages: 13

Brand: Digisol Pages: 22

Brand: AMX Pages: 1

Brand: Alula Pages: 4

Brand: B&B Electronics Pages: 17

Brand: ADTRAN Pages: 161

CORE 2 DUO E4000 - 3-2008

Brand: Intel Pages: 122

Brand: Aleratec Pages: 16

PCI-AD-x16HE-BG4

Brand: Serial Cables Pages: 18

Brand: IBM Pages: 242

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands