MTU 12V2000G series Operating Instructions Manual Download

Page: 161 / 177

7.17.3 Engine governor plug connections – Check

Preconditions

☑

Engine stopped and starting disabled.

☑

Electronic engine management system is de-energized.

NOTICE

Insertion of unsuitable test probe, e.g. test prod.
The contacts in the plug connection can be bent!
• Carry out check of plug connection only with test connectors.

Checking plug connections at engine governor

Check all plug connections for secure seating.

Lock loose connectors.

Check dust cap on ECU and EXU connectors for damage and correct seating.

MS15054/00E 2015-09

| Task Description | 161

TIM-ID: 0000000048 - 009

Summary of Contents for 12V2000G series


















































































































































































Search results

Summary of Contents for 12V2000G series

Reviews:

Related manuals for 12V2000G series

Brands by name

Popular brands

MTU 12V2000G series, Operating Instructions Manual

Search results

Summary of Contents for 12V2000G series

Reviews:

Related manuals for 12V2000G series

Brands by name

Popular brands