MTU 12 V 4000 M33F Operating Instructions Manual Download Page 69

Page: 69 / 282

STARTING (with compressed air/hydraulic starter)

Heat exchanger

installed

Heat exchanger

separate

Starting-air pressure before starter motor,
min.

bar

Starting-air pressure before starter, max.

bar

CAPACITIES

Heat exchanger

installed

Heat exchanger

separate

Engine coolant, engine side (with cooling
system)

Liters

350

Total engine oil capacity at initial filling
(standard oil system) (option: max. operat-
ing inclinations)

Liters

Oil change quantity, max. (standard oil
system) (option: max. operating inclina-
tions)

Liters

280

Oil pan capacity at dipstick mark “min.”
(standard oil system) (option: max. operat-
ing inclinations)

Liters

210

Oil pan capacity at dipstick mark “max.”
(standard oil system) (option: max. operat-
ing inclinations)

Liters

250

WEIGHTS / MAIN DIMENSIONS

Heat exchanger

installed

Heat exchanger

separate

Engine dry weight (with attached standard
accessories, without coupling)

9020

8590

ACOUSTICS

Heat exchanger

installed

Heat exchanger

separate

Exhaust noise, unsilenced - DL (free-field
sound pressure level Lp, 1m distance, ISO
6798, +3dB(A) tolerance)

dB(A)

109

MS150069/02E 2014-03

| Product Summary | 69

TIM-ID: 0000022943 - 001

Summary of Contents for 12 V 4000 M33F



























































































































































































































































































Search results

Summary of Contents for 12 V 4000 M33F

Reviews:

Related manuals for 12 V 4000 M33F

Brands by name

Popular brands

MTU 12 V 4000 M33F, Operating Instructions Manual

Search results

Summary of Contents for 12 V 4000 M33F

Reviews:

Related manuals for 12 V 4000 M33F

Brands by name

Popular brands