manualshive.com logo in svg

MTU 12 V 4000 M33F, Operating Instructions Manual

Share
Download
MTU 12 V 4000 M33F Operating Instructions Manual Download Page 243

6.15.11 Preheater – Function and leak-tightness check

Preconditions

☑

Preheater is switched on.

WARNING

Coolant is hot and highly pressurized.

Risk of injury! Risk of scalding!
• Allow engine to cool down.
• Wear protective clothing, protective gloves, and safety glasses / facial protection.

Checking operation

Note:

The coolant temperature must correlate to the control range of the thermostat when the preheater is
ready for operation.

1.

Check coolant preheating temperature.

2.

Set the thermostat accordingly if the temperatures are not in the control range.

Checking for leaks

1.

Check leak-tightness at coolant inlet and outlet.

2.

Tighten any leaking unions.

MS150069/02E 2014-03

| Task Description | 243

TIM-ID: 0000048882 - 001

Summary of Contents for 12 V 4000 M33F



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands