MTU 12 V 4000 M33F Operating Instructions Manual Download Page 200

Page: 200 / 282

6.8 Exhaust Turbocharger

6.8.1 Compressor wheel – Cleaning

Preconditions

☑

Engine is stopped and starting disabled

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 10-60 Nm

F30452769

Ratchet adapter

F30027340

Cleaner

40377

Engine oil
Engine coolant
Sealing rings

(→ Spare Parts Catalog)

Sealing rings

(→ Spare Parts Catalog)

WARNING

Chemical substances.

Risk of irritation and chemical burns!
• Observe the instructions of the cleaning agent manufacturer.

NOTICE

Inappropriate cleaning tool.

Risk of damage to component!
• Observe manufacturer's instructions.
• Use appropriate cleaning tool.

NOTICE

Incorrect installation of components and lines.

Damage to component!
• Ensure that components/lines are installed so that they are never under tension or strain.
• Ensure correct installation position of components.

Preparatory steps – Horizontal air intake

Drain engine coolant (→ Page 231).

Remove air filter (→ Page 210).

Seal all openings with suitable covers.

200 | Task Description | MS150069/02E 2014-03

TIM-ID: 0000018629 - 006

Summary of Contents for 12 V 4000 M33F



























































































































































































































































































Search results

Summary of Contents for 12 V 4000 M33F

Reviews:

Related manuals for 12 V 4000 M33F

Brands by name

Popular brands

MTU 12 V 4000 M33F, Operating Instructions Manual

Search results

Summary of Contents for 12 V 4000 M33F

Reviews:

Related manuals for 12 V 4000 M33F

Brands by name

Popular brands