MSA V-Gard HP High, Operating Manual

Page: 83 / 108

MF
83
DESCRIPTION
These ear-muffs are designed to reduce exposure to harmful levels of noise. To ensure you get the best comfort, fit and function
out of the product, it is important that you read the instructions carefully and save them for future reference.
For further details on noise reduction, refer to Table 1. Make sure you have selected the correct product for your application.
TESTING & APPROVALS
The Noise Reduction Rating (NRR) is third-party tested in accordance with ANSI S3.19-1974. It also meets CSA Class.
Dispose of the ear-muffs in accordance with national legislation.
MARKING EXPLANATION
- CE 0082: CE mark with four digit identification number of the European Notified Body APAVE (plant audit).
- IRAM S: Legal mark for Argentina approval.
- CAxxxx: Legal mark for Brazilian approval.
- AS/NZS 1270 SMK40961: Legal mark for Australian and New Zealand approval.
- HIGH / MEDIUM / LOW: Hearing protection version.
The Declaration of Conformity can be found under the following link: https://MSAsafety.com/DoC.
FITTING INSTRUCTIONS
Before following the fitting instructions below, brush excess hair aside and remove any ear jewelry that could affect
acoustic seal. The cushions must form a tight seal against the head. Interference with the seal by an object such as,
but not limited to, respirator straps or spectacle arms, can reduce the noise attenuation of the ear-muffs. The cups must
completely enclose the ears.
A & B: Fitting the cups. Pull the cups down to the lower position and lift the blades until the springs click up (pic. A ).
Push the attachment blade firmly into the slot on the side of the helmet until it clicks into place (pic.
B
).
C: Working position. Adjust the cups until they are comfortable. Make sure that the cushions seal tightly around the ears.
Note : In noisy environments, the ear-muffs must be worn in the working position at all times.
D: Stand-by position. Pull the ear-muffs away from the ear until they lock into the stand-by position.
E: Parking position.
First, lift the cups to the stand-by position, and then rotate them up to the next fixed position. In
this position, the cushions do not get damaged or dirty and the cups can dry out on the inside.
Note: Do not press the cups onto the helmet shell as this will lock the springs in the ear-muff arms, and damage the
attachment slots on the side of the helmet.
F: Storage position.
When the helmet is not in use, lower the ear-muffs and press them inward.
OPERATION / STORAGE TEMPERATURE
-20 °C (4 °F) to +50 °C (122 °F)
STORAGE
When the ear-muffs are not in use, store them in such a way that the cushions are not compressed. Keep the ear-muffs
dry and clean, store them at normal room temperature and do not place them in direct sunlight.
MAINTENANCE
Clean and disinfect the cups, cushions and inserts with mild soap and water only. Ear-muffs, and in particular cushions,
may deteriorate with use. MSA recommends to examine ear-muffs and cushions at frequent intervals for cracking and
leakage, e.g. at the start of every working shift.
HYGIENE KITS
The cushions and inserts are replaceable. Always replace worn or damaged parts (pic. G). Use only hygiene kits from MSA,
consisting of one pair of cushions and one pair of inserts. MSA recommends to replace the hygiene kit at least twice a year
for standard use to ensure that the noise attenuation performance is maintained. For ordering reference, refer to Table 3.
When installing the hygiene kits, ensure that the inserts are fully seated in the cup of the hearing protector before installing
the cushion. Ensure that the insert is not pinched between the cushion and the cup of the hearing protector when the
cushion is installed.
WARNING!
• If the insert is pinched between the cushion and the cup of the hearing protector, the acoustic performance can be
affected.
Failure to follow this warning can result in serious injury including but not limited to permanent hearing loss.
US