MQ Power DCA220SSJU4F Operation Manual Download Page 78

Page: 78 / 80

PAGE 78 — DCA220SSJU4F 60 HZ GENERATOR • OPERATION MANUAL — REV. #3 (02/10/17)

BASLER DGC-2020 PROGRAMMING APPENDIX (OPTION)

LCD Contrast

Adjust this setting to compensate for your LCD viewing angle, the available ambient light, or the ambient

temperature. This setting accepts values from 0 to 100, in increments of 1 percent.

Invert Display

When enabled, the LCD background is dark with light text.

Sleep Mode

Select

enabled

to send the DGC-2020HD into sleep mode during periods of inactivity to minimize battery

drain.

LCD Backlight Timeout

When Sleep Mode is enabled, this setting dictates the amount of time that must elapse before the DGC-

2020HD enters sleep mode. This setting accepts values from 1 to 120, in increments of 1 minute.

Language Selection

Front panel text is displayed in the selected language. Select English, French, Spanish, or German.

Screen Scrolling Setup

When scrolled metering is enabled, user-selected metering values are displayed on the overview screen.

Any number of the available values can be displayed. Up to nine values are displayed on the screen at

one time, after the scroll time delay has elapsed, the next set of values is displayed and so on.

Initializing Messages

Two custom initializing messages are displayed on the boot screen of the DGC-2020HD.

Touchscreen Disable

When checked, the touch screen controls are disabled.

Splash Screen

BESTCOMSPlus

Navigation Path:

Settings Explorer, General Settings, Splash Screen

Front Panel Navigation Path:

Not available through front panel

A splash screen, which is displayed for a few seconds upon powering up the DGC-2020HD, can be

customized. The image must be exactly 480 pixels wide and 272 pixels high. Acceptable image formats

are BMP, JPG, GIF, and PNG. This is only available to units with the optional color touch screen (style

xTxxxxxxx).
Connect to the unit using BESTCOMS

Plus

. Click the Browse button on the Splash Screen, navigate to

the desired image, select it, and click Open. If successful, the image appears in the Splash Screen in

BESTCOMS

Plus

. Upload settings to the DGC-2020HD to transfer the image.

Summary of Contents for DCA220SSJU4F

















































































Search results

Summary of Contents for DCA220SSJU4F

Reviews:

Related manuals for DCA220SSJU4F

Brands by name

Popular brands

MQ Power DCA220SSJU4F, Operation Manual

Search results

Summary of Contents for DCA220SSJU4F

Reviews:

Related manuals for DCA220SSJU4F

Brands by name

Popular brands