Motorola MT7711 User Manual Download | Manualshive

Page: 22 / 83

background image

22

Operating on Battery Power after Power Loss

When an optional Motorola-supplied or a separately purchased MTRLC LLC
(part number 98250) battery is installed, your MT7711 will automatically fail
over to battery power if there is a power outage at your location. The battery
will support standby operation for Tel1 for up to eight hours, and talk time
of up to five hours. Note that attached phones such as cordless phones that
require their own power will require their own backup power source.
Standard corded handsets do not require their own backup power source.

When running under battery backup power, only the Tel1 and Battery lights
remain lit. The battery light behaves according to this table:

Battery

Green

OFF:

No battery installed,
depleted battery, or not
provisioned for phone service

Slow
Blinking:

Battery is charging

Fast
Blinking:

Steady ON:

Battery is not charging or
Depleted; or if on back-up
power, battery is low.
AC Power Fail / Battery
back-up active

During battery backup, the Battery light will remain ON until it is almost
depleted. Then it will go into a Fast Blinking mode until it is exhausted.

The

Battery Purchase or Replacement

section on page 19 describes how

you can make sure you have phone service even if your MT7711 loses
power.

«
...
20
21
22
23
24
...
»

Summary of Contents for MT7711




















































































Reviews:

No comments

Related manuals for MT7711

Brand: T-Mobile Pages: 2

SURFboard SB2100

Brand: General Instrument Pages: 2

AirLink Raven X for Bell

Brand: Airlink101 Pages: 37

Brand: D-Link Pages: 3

Brand: BlueTree Pages: 28

Brand: Vega Absolute Pages: 23

Brand: ComBlock Pages: 22

Brand: Tait Pages: 38

COMSPHERE 3811Plus

Brand: Paradyne Pages: 13

Brand: Cradlepoint Pages: 2

COR IBR1100 series

Brand: Cradlepoint Pages: 161

Brand: Skyway Pages: 23

Brand: SMC Networks Pages: 2

Brand: Raymar Pages: 2

Brand: Zhone Pages: 2

MobiiBroadband 3G

Brand: iiNet Pages: 30

Brand: Franklin Technology Pages: 40

Brand: Assured Wireless Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands