Motorola MC92603 Reference Manual Download Page 44 | Manualshive

Page: 44 / 134

background image

3-4

MC92603 Quad Gigabit Ethernet Transceiver Reference Manual

MOTOROLA

Receiver Interface Signals

COMPAT

IEEE Std. 802.3-2002
compatibility mode enable

Indicates that the receiver is in a IEEE Std.
802.3-2002 compliant mode. If code group
addition/deletion is required to maintain
alignment, then special rules are followed that
non-intrusive to the IEEE Std. 802.3-2002
packet streams. See Section 3.7.2, “Rate
Adaption of Ethernet Packet Data Streams,” for
more information.

Input

High

XCVR_x_LBE

Enable loopback

Indicates that data into the receiver is to be taken
from the corresponding transmitter.

Input

High

DROP_SYNC

Drop synchronization

DROP_SYNC may be used with
XCVR_x_DISABLE to force a receiver to resync,
but it does not affect the transmitter operation.

Input

High

RCCE

Recovered clock enable

Indicates that the output data is synchronized to
a recovered clock.

Input

High

ADIE

Add/delete idle enable

Indicates that the receiver is free to add/delete
code groups to/from the output data stream to
maintain alignment. See Section 3.7.2, “Rate
Adaption of Ethernet Packet Data Streams,” for
more information. This input is ignored if RCCE
is high.

Input

High

TBIE

Ten-bit interface enable

Indicates that the receiver interface is in a 10-bit
mode, and that the 8B/10B decoder is bypassed.

Input

High

HSE

Half-speed enable

Indicates that the link and data interfaces are to
be operated at half-speed.

Input

High

REPE

Repeater mode enable

Causes data received to be transmitted over the
corresponding transmit channel. See
Section 5.5, “Repeater Mode,” for details.

Input

High

ENAB_RED

Enable redundant mode

Enable redundant link operation.

Input

High

XCVR_x_RSEL

Select redundant channel Receive data from secondary (redundant)

channel.

Input

High

MEDIA

Media impedance select

Indicates the impedance of the transmission
media. When the MEDIA signal is negated low, it
indicates 50

Ω

and when asserted high, it

indicates 75

Ω

.

Input

—

RECV_CLK_CENT

Center recovered clock

Indicates that the recovered clocks
(RECV_x_RCLK and RECV_x_RCLK_B) will be
centered relative to the receive data and status
outputs.

Input

High

TST_0/TST_1

Test mode

Indicates the operating/test mode of the device.

Input

—

REF_CLK_P/N

PLL reference clock

PLL reference clock input. The signal also
provides reference frequency for the receiver
interface when recovered clock mode is disabled
(RCCE is low).

Input

—

RLINK_x_N/
RLINK_x_P

Link serial receive data

Differential serial receive data input pads

Input

—

Internal Signals

rx_clock

High-speed clock

Internal, differential high speed clock, used to
transmit and receive link data.

Input

—

loop_back_data

Loopback data

Differential loopback receive data

Input

—

repeat_data

Repeater data

Data received that is looped to the transmitter if
in repeater mode (REPE is asserted high). Test
feature only.

Output

—

Table 3-1. MC92603 Receiver Interface Signals (continued)

Signal Name

Description

Function

Direction

Active

State

«
...
42
43
44
45
46
...
»

Summary of Contents for MC92603







































































































































Reviews:

No comments

Related manuals for MC92603

Brand: Hama Pages: 10

Brand: TP-Link Pages: 2

Brand: Kohler Pages: 32

Brand: Zhone Pages: 2

Brand: National Instruments Pages: 26

Brand: PairGain Pages: 80

Brand: RTS Pages: 3

Brand: iNetVu Pages: 20

Brand: Deliberant Pages: 16

Brand: Zhone Pages: 53

Brand: Planet Pages: 66

Brand: rtd Pages: 28

Brand: Allied Telesis Pages: 2

Brand: H3C Pages: 11

Brand: Crestron Pages: 32

Brand: LiveAction Pages: 2

Brand: Vonets Pages: 9

Brand: PROLiNK Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands