manualshive.com logo in svg

Motorola M-CORE MMC2001 Series, Reference Manual

The Motorola M-CORE MMC2001 Series Reference Manual is the ultimate guide to unlocking the full potential of your device. This comprehensive manual provides step-by-step instructions and valuable tips to ensure optimal performance. Download this manual for free from our website today to maximize your Motorola experience.

Share
Download
background image

MMC2001

PROGRAMMING REFERENCE

MOTOROLA 

REFERENCE MANUAL

C-39 

The transmitter FIFO cannot be written when this bit is cleared.

0 =

Transmitter disabled

1 =

Transmitter enabled

At reset, this bit is cleared to zero.

RxFL — Receiver FIFO Interrupt Trigger Level

These bits control the threshold at which a maskable interrupt is generated by the
receiver. A maskable interrupt is generated whenever the data level in the RX FIFO
reaches the selected threshold. 

At reset, these bits are cleared to zero.

RRDYEN — Receiver Ready Interrupt Enable

Setting this bit enables an interrupt when the receiver has data in the RX FIFO. The
fill level in the RX FIFO at which an interrupt is generated is controlled by the RxFL
bits. Clearing this bit disables RX interrupts.

0 =

RX interrupt disabled

1 =

RX interrupt enabled

At reset, this bit is cleared to zero.

RXEN — Receiver Enable

Setting this bit enables the receiver. If the RXD line is already low when the receiver is
enabled, the receiver does not recognize break characters, since it requires a valid
one-to-zero transition before it can accept any character.

0 =

Receiver disabled

1 =

Receiver enabled

At reset, this bit is cleared to zero.

IREN — Infrared Interface Enable

This active high bit enables the infrared interface.

0 =

Infrared interface disabled

1 =

Infrared interface enabled

At reset, this bit is cleared to zero.

RTSD EN — RTS Delta Interrupt Enable

This bit enables or disables RTS delta interrupts. The current status of the RTS pin is
read in the UART status register.

0 =

RTS interrupt disabled

1 =

RTS interrupt enabled

At reset, this bit is cleared to zero.

Table C-19 RxFL Field Settings

Value

Meaning

00

Interrupt if RX FIFO contains one or more character

01

Interrupt if RX FIFO contains four or more characters

10

Interrupt if RX FIFO contains eight or more characters

11

Interrupt if RX FIFO contains fourteen or more characters

 

   

  

Freescale Semiconductor,

 I

                                               

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

nc.

..

Summary of Contents for M-CORE MMC2001 Series




































































































































































































































































Reviews:

No comments

Related manuals for M-CORE MMC2001 Series

Eaton SC300 Operation Handbook preview
SC300
Brand: Eaton Pages: 166
Fairchild 63 Installation, Operation And Maintenance Instructions preview
63
Brand: Fairchild Pages: 2
Bartlett Genesis LT3140 Technical Manual preview
Genesis LT3140
Brand: Bartlett Pages: 5
Caen V793 Technical Information Manual preview
V793
Brand: Caen Pages: 20
FAAC E124 Original Instructions Manual preview
E124
Brand: FAAC Pages: 44
Industrial Shields M-DUINO PLUS series User Manual preview
M-DUINO PLUS series
Brand: Industrial Shields Pages: 46
National Instruments MXI-Express Gen-3 x16 User Manual preview
MXI-Express Gen-3 x16
Brand: National Instruments Pages: 38
E-T-A EtherNetIP ControlPlex CPC12EN Quick Start Manual preview
EtherNetIP ControlPlex CPC12EN
Brand: E-T-A Pages: 7
QSC TSC-101-G3 User Manual preview
TSC-101-G3
Brand: QSC Pages: 13
Holars AS H-TAG User Manual preview
H-TAG
Brand: Holars AS Pages: 15
SMC Networks ITV 0 Series Instruction Manual preview
ITV 0 Series
Brand: SMC Networks Pages: 2
Belimo GM24A-MOD Technical Data Sheet preview
GM24A-MOD
Brand: Belimo Pages: 6
Danfoss VLT LCP 601 Installation Manual preview
VLT LCP 601
Brand: Danfoss Pages: 8
LEGRAND 0 663 37 Quick Manual preview
0 663 37
Brand: LEGRAND Pages: 2
White Rodgers 50M58-289 Installation Instructions Manual preview
50M58-289
Brand: White Rodgers Pages: 8
ATTO Technology FibreBridge 7500 Getting Started Manual preview
FibreBridge 7500
Brand: ATTO Technology Pages: 2
Micro ID Sdn Bh MZ11D7 Quick Start Manual preview
MZ11D7
Brand: Micro ID Sdn Bh Pages: 7
North Star 2287181 Owner'S Manual preview
2287181
Brand: North Star Pages: 32

Brands by name

Popular brands

Load more brands