manualshive.com logo in svg

Motorola M-CORE MMC2001 Series, Reference Manual

The Motorola M-CORE MMC2001 Series Reference Manual is the ultimate guide to unlocking the full potential of your device. This comprehensive manual provides step-by-step instructions and valuable tips to ensure optimal performance. Download this manual for free from our website today to maximize your Motorola experience.

Share
Download
background image

MOTOROLA

OnCE™ DEBUG MODULE

MMC2001 

16-16

REFERENCE MANUAL

When the trace counter decrements to zero, the OnCE control logic requests that the
processor re-enter debug mode, and the trace occurrence bit TO in the OSR is set to
indicate that debug mode has been requested as a result of the trace count function.
The trace counter allows a minimum of two instructions to be specified for execution
prior to entering trace (specified by a count value of one), unless the sequential
breakpoint control capability described in 16.6.2 OnCE Control Register (OCR) is
being used. In this case a value of zero (indicating a single instruction) is allowed.

16.10 Methods of Entering Debug Mode

The OSR indicates that the CPU has entered debug mode via the PM status field.
The following paragraphs discuss conditions that invoke debug mode. 

16.10.1 Debug Request During RESET 

When the DR bit in the OCR is set, assertion of RESET causes the device to enter
debug mode. In this case the device may fetch the reset vector and the first instruc-
tion of the reset exception handler but does not execute an instruction before entering
debug mode.

16.10.2 Debug Request During Normal Activity

Setting the DR bit in the OCR during normal device activity causes the device to fin-
ish the execution of the current instruction and then enter debug mode. Note that in
this case the device completes the execution of the current instruction and stops after
the newly fetched instruction enters the CPU instruction latch. This process is the
same for any newly fetched instruction, including instructions fetched by interrupt pro-
cessing or those that will be aborted by interrupt processing. 

16.10.3 Debug Request During Stop, Doze, or Wait Mode

Setting the DR bit in the OCR when the device is in stop, doze, or wait mode (i. e.,
has executed a stop, doze, or wait instruction) causes the device to exit the low-
power state and enter the debug mode. Note that in this case, the device completes
the execution of the stop, doze, or wait instruction and halts after the next instruction
enters the instruction latch.

16.10.4 Software Request During Normal Activity

Executing the bkpt instruction when the FDB (force debug enable mode) control bit in
the control state register is set, causes the CPU to enter debug mode after the
instruction following the bkpt instruction has entered the instruction latch.

16.10.5 Enabling OnCE Trace Mode

When the OnCE trace mode mechanism is enabled and the trace count is greater
than zero, the trace counter is decremented for each instruction executed. Complet-
ing execution of an instruction when the trace counter is zero causes the CPU to
enter debug mode. 

 

   

  

Freescale Semiconductor,

 I

                                               

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

nc.

..

Summary of Contents for M-CORE MMC2001 Series




































































































































































































































































Reviews:

No comments

Related manuals for M-CORE MMC2001 Series

J+J J4C S20 Quick Start Manual preview
J4C S20
Brand: J+J Pages: 4
ABB RHD8000 Series Instructions Manual preview
RHD8000 Series
Brand: ABB Pages: 17
WAC T24-OD-CTR Installation Instruction preview
T24-OD-CTR
Brand: WAC Pages: 5
NEC uPD78F4225Y Manual preview
uPD78F4225Y
Brand: NEC Pages: 30
National Instruments cRIO-9064 User Manual preview
cRIO-9064
Brand: National Instruments Pages: 26
Holars AS H-TAG User Manual preview
H-TAG
Brand: Holars AS Pages: 15
Zamel RTD-02 Manual Instruction preview
RTD-02
Brand: Zamel Pages: 2
Yaesu G-450A User Manual preview
G-450A
Brand: Yaesu Pages: 15
Milesight UC50 Series User Manual preview
UC50 Series
Brand: Milesight Pages: 28
SECO-LARM ENFORCER SLI PR-B1124-PQ Additional Information preview
ENFORCER SLI PR-B1124-PQ
Brand: SECO-LARM Pages: 2
ULTRAFRYER Ultrastat 23 Programming Manual preview
Ultrastat 23
Brand: ULTRAFRYER Pages: 1
Danfoss MCI 50-3 I-O Instructions preview
MCI 50-3 I-O
Brand: Danfoss Pages: 2
StudioComm 760-03 User Manual preview
760-03
Brand: StudioComm Pages: 55
Bamo BAMOPHOX 436 E Instruction Manual preview
BAMOPHOX 436 E
Brand: Bamo Pages: 12
RJX Hobby seriously pro User Manual preview
seriously pro
Brand: RJX Hobby Pages: 11
V2 PESO-230V Manual preview
PESO-230V
Brand: V2 Pages: 108
SMC Networks LEC Series Operation Manual preview
LEC Series
Brand: SMC Networks Pages: 50
Quick-Ohm QC-PC-CO-CH1 User Manual preview
QC-PC-CO-CH1
Brand: Quick-Ohm Pages: 4

Brands by name

Popular brands

Load more brands