manualshive.com logo in svg

Motorola M-CORE MMC2001 Series, Reference Manual

The Motorola M-CORE MMC2001 Series Reference Manual is the ultimate guide to unlocking the full potential of your device. This comprehensive manual provides step-by-step instructions and valuable tips to ensure optimal performance. Download this manual for free from our website today to maximize your Motorola experience.

Share
Download
background image

MMC2001

OnCE™ DEBUG MODULE

MOTOROLA 

REFERENCE MANUAL

16-15 

Figure 16-8 OnCE Trace Logic Block Diagram

16.9.1 Trace Counter (OTC)

The trace counter (OTC) allows more than one instruction to be executed in real time
before the device returns to debug mode. This feature helps the software developer
debug sections of code that are time-critical. The trace counter also enables the user
to count the number of instructions executed in a code segment.

The OTC is a 16-bit counter that can be read, written, or cleared through the OnCE
serial interface. If N instructions are to be executed before entering debug mode, the
trace counter should be loaded with N–1. N must not equal zero unless the sequential
breakpoint control capability described in 16.6.2 OnCE Control Register (OCR) is
being used. In this case a value of zero (indicating a single instruction) is allowed.

The trace counter is cleared by hardware reset.

16.9.2 Trace Operation

The following steps initiate trace mode operation:

1. Load the counter with a value. This value must be non-zero, unless the sequential

breakpoint control capability described in 16.6.2 OnCE Control Register (OCR) is
being used. In this case a value of zero (indicating a single instruction) is allowed.

2. Initialize the program counter and instruction register in the CPUSCR with values

corresponding to the start location of the instruction(s) to be executed real-time.

3. Set the TME bit in the OCR.

4. Release the processor from debug mode by executing the appropriate command

issued by the external command controller.

When debug mode is exited, the counter is decremented after each execution of an
instruction. Interrupts can be serviced, and all instructions executed (including inter-
rupt services) will decrement the trace counter.

DSI

DSO

DSCK

DEC

End of Instruction

COUNT=0

ISTRACE

.

.

Trace Counter

 

   

  

Freescale Semiconductor,

 I

                                               

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

nc.

..

Summary of Contents for M-CORE MMC2001 Series




































































































































































































































































Reviews:

No comments

Related manuals for M-CORE MMC2001 Series

Panasonic FP-I4C User Manual preview
FP-I4C
Brand: Panasonic Pages: 31
Panasonic EYFR03 Training Manual preview
EYFR03
Brand: Panasonic Pages: 31
NAiS FP Series Hardware Manual preview
FP Series
Brand: NAiS Pages: 199
Panasonic CZ-ANC2 Instruction Manual preview
CZ-ANC2
Brand: Panasonic Pages: 38
Panasonic CZ-256ESMC3 Quick Reference preview
CZ-256ESMC3
Brand: Panasonic Pages: 36
Panasonic CZ-256ESMC3 Technical Data Manual preview
CZ-256ESMC3
Brand: Panasonic Pages: 179
Panasonic AW-RP60G Operating Manual preview
AW-RP60G
Brand: Panasonic Pages: 23
IFM CR710S Original Operating Instructions preview
CR710S
Brand: IFM Pages: 49
Vacon 100X series Installation, Technical And Maintenance Manual preview
100X series
Brand: Vacon Pages: 132
SOMFY Situo 1 RTS Installation And Operating Manual preview
Situo 1 RTS
Brand: SOMFY Pages: 112
Epsolar eTracer ET4415BND Operation Manual preview
eTracer ET4415BND
Brand: Epsolar Pages: 44
Barco EC-210 Quick Start Manual-Setup preview
EC-210
Brand: Barco Pages: 4
Zonex DIGI3U Installation Manual preview
DIGI3U
Brand: Zonex Pages: 16
Lennox HYDROCONTROL Installation, Operating And Maintenance Manual preview
HYDROCONTROL
Brand: Lennox Pages: 34
Rohde ST 630 Operation Manual preview
ST 630
Brand: Rohde Pages: 344
OCTANORM M 1497-4 User Manual preview
M 1497-4
Brand: OCTANORM Pages: 6
Fairchild HPD1***A**K*N Installation, Operation And Maintenance preview
HPD1***A**K*N
Brand: Fairchild Pages: 4
S+S Regeltechnik HYGRASREG KH-10 Operating Instructions, Mounting & Installation preview
HYGRASREG KH-10
Brand: S+S Regeltechnik Pages: 16

Brands by name

Popular brands

Load more brands