manualshive.com logo in svg

Motorola M-CORE MMC2001 Series, Reference Manual

The Motorola M-CORE MMC2001 Series Reference Manual is the ultimate guide to unlocking the full potential of your device. This comprehensive manual provides step-by-step instructions and valuable tips to ensure optimal performance. Download this manual for free from our website today to maximize your Motorola experience.

Share
Download
background image

MMC2001

INTERVAL MODE SERIAL PERIPHERAL INTERFACE

MOTOROLA 

REFERENCE MANUAL

12-3 

12.2.2 Interval (Master) Mode

Interval mode provides the user with the ability to exchange data at programmed peri-
odic intervals. This rate is controlled by three counters: the bit counter, the baud
counter, and the ISPI interval timer. This mode begins operation as soon as the
IVL_EN bit is set in the ISPI control register. (If a transfer is in progress, then opera-
tion begins upon completion of the existing transfer.) In interval mode (in contrast to
manual mode), the SPI_EN pin is active only when a transfer is in progress; that is, in
interval mode the state machine controls the enable pin. The SPI_EN enable bit (bit
12) must still be set in the ISPI control register.

An interval begins with the loading of the actual ISPI interval timer. Once this decre-
menting counter reaches zero, the state machine begins the data transfer. When the
transfer is completed, an interrupt is generated (if enabled by IRQ_EN), and the inter-
val is completed. At this point the ISPI automatically begins another interval by
reloading the interval timer. The length of an interval is governed by the following
equation:

Time_of_Interval = (HI_REFCLK_Period * 2 * (Interva2)) + 

(HI_REFCLK_Period * Baud_Count * (Cloc1))

12.2.3 Slave Mode 

In slave mode, data exchanges are controlled by external devices through the pins
SPI_CLK and SPI_EN. If pin SPI_EN is enabled (low), then data is latched into the
shift register on every other edge of SPI_CLK; the latching edge is determined by the
POL and PHA bits in the ISPI control register. Data is transferred from the shift regis-
ter to the ISPI (Rx) data register when pin SPI_EN becomes inactive, or when the bit
counter times out. In addition, IRQ is set at that time (if permitted by IRQ_EN). If the
RX data register is not unloaded prior to a new reload, the OVR (ISPI overrun) bit is
set in the ISPI status register, and the data is overwritten, causing prior received data
to be lost.

SPI_CLK must not exceed HI_REFCLK/16.

12.3 Signal Descriptions

12.3.1 SPI_MISO (Master In, Slave Out)

In either master mode, this pin is the input to the shift register. A new bit is shifted in
on each leading edge of SPI_CLK in normal clock mode or on each trailing edge of
SPI_CLK in inverted clock mode. In slave mode, this pin is the output of the shift reg-
ister. A new data bit is presented on each trailing edge of the SPI_CLK in normal
clock mode (PHA=0). As a slave mode output, SPI_MISO is three-stated when the
SPI_EN input is negated.

 

   

  

Freescale Semiconductor,

 I

                                               

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

nc.

..

Summary of Contents for M-CORE MMC2001 Series




































































































































































































































































Reviews:

No comments

Related manuals for M-CORE MMC2001 Series

ABB XFC G5 Quick Start Manual preview
XFC G5
Brand: ABB Pages: 2
BEIER-Electronic SV1-2-10Z Instruction Manual preview
SV1-2-10Z
Brand: BEIER-Electronic Pages: 22
Namron ZigBee Quick Start Manual preview
ZigBee
Brand: Namron Pages: 3
Rain Bird PAR+ES Installation Manual preview
PAR+ES
Brand: Rain Bird Pages: 24
Rain Bird ESP-LXIVM Series Device Installation Manuallines preview
ESP-LXIVM Series
Brand: Rain Bird Pages: 16
Xylem CentriPro Aquavar SOLO Instruction Manual preview
CentriPro Aquavar SOLO
Brand: Xylem Pages: 48
DeLaval MPCII Memo preview
MPCII
Brand: DeLaval Pages: 102
Purmo NC 24 V Assembly Instructions preview
NC 24 V
Brand: Purmo Pages: 2
salmson ACSON VARIO Installation And Starting Instructions preview
ACSON VARIO
Brand: salmson Pages: 78
D+H DXD 150-BSY+ Original Instructions Manual preview
DXD 150-BSY+
Brand: D+H Pages: 16
Phoenix Contact 2297031 Manual preview
2297031
Brand: Phoenix Contact Pages: 56
Fairford Synergy SGY-101 Quick Start Manual preview
Synergy SGY-101
Brand: Fairford Pages: 20
ST UM1932 User Manual preview
UM1932
Brand: ST Pages: 40
Varian 969-9507 Instruction Manual preview
969-9507
Brand: Varian Pages: 37
QUANT QUANT-14 Operation Manual preview
QUANT-14
Brand: QUANT Pages: 24
PPI Zenex Plus User Manual preview
Zenex Plus
Brand: PPI Pages: 27
SUPMEA SUP-PH8.0 User Manual preview
SUP-PH8.0
Brand: SUPMEA Pages: 32
Citadele Digipass 320 Operation Instructions Manual preview
Digipass 320
Brand: Citadele Pages: 6

Brands by name

Popular brands

Load more brands