Motorola DSP56309 User Manual Download Page 304 | Manualshive

Page: 304 / 425

background image

JTAG Port

Introduction

MOTOROLA

DSP56309UM/D 11-3

11.1

INTRODUCTION

The DSP56300 core provides a dedicated user-accessible test access port (TAP) that is
fully compatible with the

I

EEE 1149.1 Standard Test Access Port and Boundary Scan

Architecture

. Problems associated with testing high density circuit boards have led to

development of this proposed standard under the sponsorship of the Test Technology
Committee of IEEE and the JTAG. The DSP56300 core implementation supports
circuit-board test strategies based on this standard.

The test logic includes a TAP that consists of five dedicated signals, a 16-state controller,
and three test data registers. A Boundary Scan Register (BSR) links all device signals into
a single shift register. The test logic, implemented utilizing static logic design, is
independent of the device system logic. The DSP56300 core implementation provides the
following capabilities:

¥ Performs boundary scan operations to test circuit-board electrical continuity

(EXTEST)

¥ Bypasses the DSP56300 core for a given circuit-board test by effectively reducing

the BSR to a single cell (BYPASS)

¥ Samples the DSP56300 core-based device system signals during operation and

transparently shifts out the result in the BSR

¥ Preloads values to output signals prior to invoking the EXTEST instruction

(SAMPLE/PRELOAD)

¥ Disables the output drive to signals during circuit-board testing (HI-Z)

¥ Provides a means of accessing the OnCE controller and circuits to control a target

system (ENABLE_ONCE)

¥ Provides a means of entering debug Mode (DEBUG_REQUEST)

¥ Queries identification information (manufacturer, part number and version) from

a DSP56300 core-based device (IDCODE)

¥ Forces test data onto the outputs of a DSP56300 core-based device while replacing

its boundary scan register in the serial data path with a single bit register
(CLAMP)

This section, which includes aspects of the JTAG implementation that are specific to the
DSP56300 core, is intended to be used with the supporting IEEE 1149.1 document. The
discussion includes those items required by the standard to be defined and, in certain
cases, provides additional information specific to the DSP56300 core implementation.
For internal details and applications of the standard, refer to the IEEE 1149.1 document.

Figure 11-1

shows a block diagram of the TAP port.

«
...
302
303
304
305
306
...
»

Summary of Contents for DSP56309










































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56309

Brand: Marani Pages: 39

Brand: Kenwood Pages: 64

Brand: Fullstar Pages: 11

Brand: izzy Pages: 26

Digital Audio Processor RDP 980

Brand: Rotel Pages: 7

Brand: Excalibur Pages: 26

Brand: Waring Pages: 64

Brand: Radial Engineering Pages: 2

Brand: eta Pages: 44

Brand: Harris Pages: 114

Symphony DSP56724

Brand: Freescale Semiconductor Pages: 436

Brand: Electrolux Pages: 12

Essentials KFP400

Brand: Kambrook Pages: 24

Brand: HAMILTON BEACH/PROCTOR SILEX Pages: 8

EASYCOMPACT EFP5 AR Series

Brand: Electrolux Pages: 40

Brand: Cuisinart Pages: 53

Brand: HOFFEN Pages: 32

Mini Wizz BFP100

Brand: Breville Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands