Motorola DSP56309 User Manual Download Page 89 | Manualshive

Page: 89 / 425

background image

3-4

DSP56309UM/D MOTOROLA

Memory Configuration

Memory Spaces

DSP56309 to feed two operands to the Data ALU simultaneously, enabling it to perform
a multiply-accumulate operation in one clock cycle.

X and Y data memory are identical in structure and functionality except for the upper
128 words of each space. The upper 128 words of X data memory are reserved for
internal I/O. We recommend that the programmer reserve the upper 128 words of Y
data memory for external I/O. (For further information, see

Section 3.1.2.1 X Data

Memory Space

Section 3.1.2.2 Y Data Memory Space

X and Y data memory space each consist of the following:

¥ Internal data memory (X data RAM and Y data RAM, the default size of each is

7K, but they can be switched to 5K each)

¥ (Optionally) Off-chip memory expansion (up to 16 M in the 24-bit address mode

and 64K in the 16-bit address mode)

3.1.2.1

X Data Memory Space

The on-chip peripheral registers and some of the DSP56309 core registers occupy the top
128 locations of X data memory ($FFFF80Ð$FFFFFF in the 24-bit Address mode or
$FF80Ð$FFFF in the 16-bit Address mode). This area is called X-I/O space, and it can be
accessed by MOVE and MOVEP instructions and by bit oriented instructions (BCHG,
BCLR, BSET, BTST, BRCLR, BRSET, BSCLR, BSSET, JCLR, JSET, JSCLR, and JSSET). For
a listing of the contents of this area, see the programming sheets in

Appendix DÑProgramming Reference

The X memory space at locations $FF0000 to $FFEFFF is reserved and should not be
accessed by the programmer.

3.1.2.2

Y Data Memory Space

The off-chip peripheral registers should be mapped into the top 128 locations of Y data
memory ($FFFF80Ð$FFFFFF in the 24-bit address mode or $FF80Ð$FFFF in the 16-bit
address mode) to take advantage of the move peripheral data (MOVEP) instruction and
the bit oriented instructions (BCHG, BCLR, BSET, BTST, BRCLR, BRSET, BSCLR, BSSET,
JCLR, JSET, JSCLR, and JSSET).

The Y memory space at locations $FF0000 to $FFEFFF is reserved and should not be
accessed by the programmer.

«
...
87
88
89
90
91
...
»

Summary of Contents for DSP56309










































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56309

INTEGRAL Series

Brand: D.A.S. Pages: 18

Brand: SunPlus Pages: 59

Brand: SOLIS Pages: 100

Brand: MIA Pages: 33

Mark Levinson N 30.6

Brand: Madrigal Audio Pages: 38

Brand: Gardol Pages: 40

Brand: Electrolux Pages: 16

Brand: NEC Pages: 3

Brand: Proctor-Silex Pages: 52

Perceptual SoundMax Q24

Brand: ATC Labs Pages: 56

Brand: BABY BOO Pages: 124

Professional MUM57B224

Brand: Bosch Pages: 52

OptiMUM 9 Series

Brand: Bosch Pages: 149

Brand: Wheatstone Pages: 142

Robot culinaire

Brand: Thinkkitchen Pages: 28

Sonic Frontiers SFD-1

Brand: Sonic Frontiers Pages: 8

Brand: Steg Pages: 11

Brand: Golden Age Project Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands