Motorola DSP56309 User Manual Download Page 295 | Manualshive

Page: 295 / 425

background image

10-26

DSP56309UM/D MOTOROLA

On-Chip Emulation Module

OnCE Module Examples

Note:

The user must read the entire FIFO, since each read increments the FIFO

pointer, thus pointing to the next FIFO location. At the end of this procedure,
the FIFO pointer points back to the beginning of the FIFO.

The information that has been read by the external command controller now contains
the address of the newly fetched instruction, the address of the instruction currently on
the PDB, the address of the instruction currently on the instruction latch, as well as the
addresses of the last 12 instructions that have been executed and are change of flow. A
user program can now reconstruct the flow of a full trace based on this information and
on the original source code of the currently running program.

10.12.5

Displaying a Specified Register

To display a specified register, the DSP56300 must be in debug mode and all actions
described in

Section 10.12.3ÑSaving Pipeline Information

have been executed. The

sequence of actions is as follows:

1. Select shift-DR. Shift in the ÒWrite PDB with GO no-EXÓ. Pass through

update-DR.

2. Select shift-DR. Shift in the 24-bit opcode: ÒMOVE reg, X:OGDBÓ. Pass through

update-DR to actually write OPDBR and thus begin executing the MOVE
instruction.

3. Wait for DSP to reenter debug mode (wait for DE or poll core status).

4. Select shift-DR and shift in ÒREAD GDB REGISTERÓ. Pass through update-DR.

This step selects OGDBR as the data register for the read.

5. Select shift-DR. Shift out the OGDBR contents. Pass through update-DR. Wait for

next command.

10.12.6

Displaying X Memory Area Starting at Address $xxxx

The DSP56309 must be in debug mode and all actions described in

Section 10.12.3ÑSaving Pipeline Information

must have been executed. Since R0 is

used as pointer for the memory, R0 is saved first. The sequence of actions is as follows:

1. Select shift-DR. Shift in the ÒWrite PDB with GO no-EXÓ. Pass through

update-DR.

«
...
293
294
295
296
297
...
»

Summary of Contents for DSP56309










































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56309

Brand: Rabe Pages: 23

ME30 infobox connect

Brand: Mauell Pages: 40

Kaleo StoreAway

Brand: T-Fal Pages: 93

Brand: Moulinex Pages: 19

Brand: Dualit Pages: 14

Brand: Hamilton Beach Pages: 96

Brand: Johnson Pages: 28

Brand: WMF Pages: 35

Brand: Kooper Pages: 23

Brand: Zelmer Pages: 86

Stack & Snap 70815

Brand: Hamilton Beach Professional Pages: 48

Silver Line SL-1543

Brand: Scarlett Pages: 26

Reveo Food Processor/Tumbler

Brand: Eastman Outdoors Pages: 34

Brand: Kasanova Pages: 32

Brand: Team Kalorik Pages: 36

Brand: Team Kalorik Pages: 36

Brand: DD Audio Pages: 14

Brand: THORLABS Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands