7-36
DSP56305 User’s Manual
MOTOROLA
Enhanced Synchronous Serial Interface (ESSI)
ESSI Programming Model
7.4.3.5
Transmitter Underrun Error Flag (TUE) SSISR Bit 4
The TUE bit is set when at least one of the enabled Serial Transmit Shift Registers is
empty (no new data to be transmitted) and a transmit time slot occurs. When a transmit
underrun error occurs, the previous data (which is still present in the TX registers that
were not written) will be retransmitted. In the Normal mode, there is only one transmit
time slot per frame. In the Network mode, there can be up to thirty-two transmit time
slots per frame. If the TEIE bit is set, a DSP transmit underrun error interrupt request is
issued when the TUE bit is set.
Hardware, software, ESSI individual, and stop reset clear TUE. TUE can also be cleared
by first reading the SSISR with the TUE bit set, then writing to all the enabled Transmit
Data Registers or to the TSR.
7.4.3.6
Receiver Overrun Error Flag (ROE) SSISR Bit 5
The ROE bit is set when the Serial Receive Shift Register is filled and ready to transfer to
the Receive Data Register (RX) but the RX is already full (i.e., when the RDF bit is set). If
the REIE bit is set, a DSP receiver overrun error interrupt request is issued when the
ROE bit is set.
Hardware, software, ESSI individual, and stop reset clear ROE. ROE can also be cleared
by reading the SSISR with the ROE bit set and then reading the RX.
7.4.3.7
ESSI Transmit Data Register Empty (TDE) SSISR Bit 6
The TDE bit is set when the contents of the Transmit Data Register of every enabled
transmitter are transferred to the Transmit Shift Register. It is also set for a TSR disabled
time slot period in Network mode (as if data were being transmitted after the TSR was
written). When set, the TDE bit indicates that data should be written to all the TX
registers of the enabled transmitters or to the TSR. The TDE bit is cleared when the
DSP56304 writes to all the Transmit Data Registers of the enabled transmitters, or when
the DSP writes to the TSR to disable transmission of the next time slot. If the TIE bit is
set, a DSP transmit data interrupt request is issued when TDE is set.
Hardware, software, ESSI individual, and stop reset clear the TDE bit.
7.4.3.8
ESSI Receive Data Register Full (RDF) SSISR Bit 7
The RDF bit is set when the contents of the Receive Shift Register are transferred to the
Receive Data Register. The RDF bit is cleared when the DSP reads the Receive Data
Register. If RIE is set, a DSP receive data interrupt request is issued when RDF is set.
Hardware, software, ESSI individual, and stop reset clear the RDF bit.
Summary of Contents for DSP56305
