manualshive.com logo in svg

Motorola DSP56305, User Manual

The Motorola DSP56305 is a versatile digital signal processor designed for a wide range of applications. To get the most out of this powerful device, make sure to download the free User Manual from our website. Explore its features and functionalities with this comprehensive manual, available for instant download at manualshive.com.

Share
Download
background image

VITERBI CO-PROCESSOR

Programming Model

MOTOROLA

DSP56305 User’s Manual

13-19

13.5.3.3

Decoding Enable (DECEN)—VCRA Bit 2

The Decoding Enable bit (DECEN), when set, enables the module to perform 
convolutional decoding. All mode parameters specifying the type of coding must be set 
prior to entering this mode (that is, the registers VCRA, VCRB, VTPA, and VTPB must 
be written, and VCNT, VWES, and VTSR may need to be written, prior to this 
operation). At the end of the decoding (i.e. after VCNT reaches zero and the flush 
operation is completed), the DECEN bit is cleared by the internal logic. When the VCOP 
is in continuous mode (CME is set), the flush operation does not take place, and DECEN 
is not cleared by the internal logic. When DECEN is cleared, the decoding operation 
halts and the register contents are preserved. The decoding operation is resumed if 
DECEN is set again.

13.5.3.4

Encoding Enable (ENCEN)—VCRA Bit 3

The Encoding Enable bit (ENCEN), when set, enables the module to perform 
convolutional encoding. All mode parameters specifying the type of the coding must be 
set prior to entering this mode; that is, the registers VCRA, VCRB, VTPA, and VTPB 
must be written, and VCNT may need to be written, prior to this operation. At the end of 
the encoding (i.e. after VCNT reaches zero) the ENCEN bit is cleared by the internal 
logic. When the VCOP is in continuous mode (CME is set), ENCEN is not cleared by the 
internal logic. When ENCEN is cleared, the encoding operation halts and the register 
contents are preserved. The encoding operation is resumed if ENCEN is set again.

13.5.3.5

Equalization Enable (EQEN)—VCRA Bit 4

The Equalization Enable bit (EQEN), when set, enables the module to perform channel 
equalization. All mode parameters specifying the type of the equalization must be set 
prior to entering this mode (that is, the registers VCRA and VCRB must be written, and 
VCNT and VTSR may need to be written, prior to this operation). Equalization uses 
S-parameters and V-parameters, therefore these values (contained in the SP RAM and 
VP RAM respectively) must be written using the Memory Access Mode prior to starting 
equalization. At the end of equalization (that is, after VCNT reaches zero and the flush 
operation is complete), the EQEN bit is cleared by the internal logic. When the VCOP is 
in continuous mode (CME is set), the flush operation does not take place, and EQEN is 
not cleared by the internal logic. When EQEN is cleared, the equalization operation halts 
and the register contents are preserved. The equalization operation is resumed if EQEN 
is set again.

13.5.3.6

Flush Enable (FLEN)—VCRA Bit 5

The Flush Enable bit (FLEN), when set, enables the module to perform the flush 
operation in order to complete the current operation prior to its normal ending (i.e. 
before the counter reaches zero), forcing the module to extract survivor path bits 
remaining in Trellis RAM. The path to be flushed is defined by the VTSR register. At the 
end of the flush operation the FLEN bit is cleared by the internal logic. 

Summary of Contents for DSP56305

























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56305

eta 0027 bross Instructions For Use Manual preview
0027 bross
Brand: eta Pages: 68
Berkel CC34 Specifications preview
CC34
Brand: Berkel Pages: 2
Gastroback Design Mini Chopper Plus Operating Instructions Manual preview
Design Mini Chopper Plus
Brand: Gastroback Pages: 48
Swann SP13040N User Manual preview
SP13040N
Brand: Swann Pages: 6
Black & Decker HandyChopper HC2000 Use And Care Book Manual preview
HandyChopper HC2000
Brand: Black & Decker Pages: 6
CONTINENTAL EDISON CERM1000B Instruction Manual preview
CERM1000B
Brand: CONTINENTAL EDISON Pages: 13
Tektronix TSG 95 Pathfinder User Manual preview
TSG 95 Pathfinder
Brand: Tektronix Pages: 83
Vitek VT-1639 Manual Instruction preview
VT-1639
Brand: Vitek Pages: 24
VAN WAMEL Perfect KT 3D-Flex Instruction Manual preview
Perfect KT 3D-Flex
Brand: VAN WAMEL Pages: 50
JBL SDP-2 Quick Reference Manual preview
SDP-2
Brand: JBL Pages: 2
HAEGER Perfect Combi 2in1 User Instructions preview
Perfect Combi 2in1
Brand: HAEGER Pages: 48
WEISS DSP501 User Manual preview
DSP501
Brand: WEISS Pages: 38
Tower Hobbies T18002 Safety And Instruction Manual preview
T18002
Brand: Tower Hobbies Pages: 16
Arbor Technology EmQ-i2301 User Manual preview
EmQ-i2301
Brand: Arbor Technology Pages: 44
Scarlett SC-HB42F18 Instruction Manual preview
SC-HB42F18
Brand: Scarlett Pages: 17
Lebensstil Kollektion LKSM-5501C Instruction Manual preview
LKSM-5501C
Brand: Lebensstil Kollektion Pages: 7

Brands by name

Popular brands

Load more brands