MOTO GUZZI V7 CLASSIC Service Manual Download Page 83

Page: 83 / 134

Co rate adjustment

It is not possible to adjust CO (time of injectors opening) but just resetting the self-adjustable parameters

in case the throttle body is replaced because it is worn.

Iso screen page

ISO

This display shows general data regarding the

control unit, for example software type, mapping,

control unit programming date

ISO DISPLAY

Specification

Desc./Quantity

Mapping

Engine parameter reading screen page

ENGINE PARAMETER READING

This display shows the parameters measured by

the several sensors (engine revs, engine temper-

ature, etc.) or values set by the control unit (injec-

tion time, ignition advance, etc.)

NGINE

PARAMETER

READING

SCREEN

PAGE

Specification

Desc./Quantity

Throttle

Value corresponding to the throttle when closed (approximate
value between 4.5 and 4.9°) (left throttle supported by the end

of stroke screw). If a different value is read, it is necessary to

activate the parameter "Throttle positioner autodetection" and

obtain this value.

TPS Trimmer

Supplementary parameter related to throttle keying in calibra-

tion.

Precise throttle position

Throttle opening angle in degrees: once the throttle position

self-learning is carried out, it falls within the following value

range: 3.1° ± 0.4°.

Lambda Probe

300 - 3000 mV (approximate values).

Signal when energised that the control unit receives from the

lambda probe: inversely proportional to the presence of oxy-

gen.

V7 Classic

Power supply

P SUPP - 83

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for V7 CLASSIC







































































































































Search results

Summary of Contents for V7 CLASSIC

Reviews:

Related manuals for V7 CLASSIC

Brands by name

Popular brands

MOTO GUZZI V7 CLASSIC, Service Manual

Search results

Summary of Contents for V7 CLASSIC

Reviews:

Related manuals for V7 CLASSIC

Brands by name

Popular brands