MOTO GUZZI V7 CLASSIC Service Manual Download Page 117

Page: 117 / 134

•

Apply suitable colours available in the

market on the pinion teeth.

•

Fit the drilled bolt-crown unit cover and

their spacers and gaskets on the hous-

ing and provisionally tighten the

screws.

•

On the crown holder drilled bolt, fit a

"Universal" extractor that with appro-

priate central spacers slightly presses

the crown towards the brake disc side.

•

Turn the pinion in the riding direction,

with the crown braked so that the rota-

tion is carried out under load, and

leaves a contact mark on the pinion

surface.

•

If the contact is regular, the mark on the

pinion teeth will be like this (the pinion

is seen from the crankshaft side

V7 Classic

Chassis

CHAS - 117

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for V7 CLASSIC







































































































































Search results

Summary of Contents for V7 CLASSIC

Reviews:

Related manuals for V7 CLASSIC

Brands by name

Popular brands

MOTO GUZZI V7 CLASSIC, Service Manual

Search results

Summary of Contents for V7 CLASSIC

Reviews:

Related manuals for V7 CLASSIC

Brands by name

Popular brands