MOTO GUZZI V7 CLASSIC Service Manual Download Page 96

Page: 96 / 134

•

Insert the cap and the well-lubricated

sealing ring on the bearing tube.

•

Use a suitable inserting tool to push the

sealing ring in the fork leg until it stops.

•

Fit the locking ring.

•

Fit the dust scraper.

•

Pour oil into the bearing tube so that it

also fills the internal grooves of the

pumping member rod.

•

Pump with the bearing tube, making

sure the oil has completely filled the

pumping member rod.

•

Introduce the spring and the preload

tube.

•

Place the cap on the bearing tube, tak-

ing care not to damage the O-ring.

Then, tighten the cap to the prescribed

torque.

Suspensions

V7 Classic

SUSP - 96

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for V7 CLASSIC







































































































































Search results

Summary of Contents for V7 CLASSIC

Reviews:

Related manuals for V7 CLASSIC

Brands by name

Popular brands

MOTO GUZZI V7 CLASSIC, Service Manual

Search results

Summary of Contents for V7 CLASSIC

Reviews:

Related manuals for V7 CLASSIC

Brands by name

Popular brands