Morgana MB300 XL Pro Operator'S Manual Download Page 81

Page: 81 / 84

MB300 XL Pro

rev.0.2 ID03570

SHAVINGS EXTRACTOR - VACUUMS LITTLE:

▪

Make sure that the shavings extractor bin is empty.

▪

Check that the inspection Plexiglas, located on the cutter is free.

▪

Make sure the vacuum hose is not full of shavings.

▪

Check that the suction filter is clean.

▪

Make sure the hose is connected

VICE - DOES NOT START:

▪

Make sure that the emergency button is disabled.

▪

Check that all doors are closed.

▪

Check the air pressure of the machine.

▪

Check that the cart is in place

▪

Is the display on the main page?

IRREGULAR GLUE START STOP:

▪

Clean the glue application unit.

▪

Verify that the temperature of the glue unit is consonant with that of the used glue.

▪

Check the state of the glue. The glue must not be inserted in the machine for too long or kept

at the working temperature. This increases the viscosity of the adhesive itself.

UNEVEN CUTTER - CUT AND RIBBING:

▪

Make sure that the teeth and notching cutter parts are not cracked or damaged. This may be caused

by books already bound with glue.

IF WE NOTICE THAT BOOKS WITH GLUE WERE MILLED, THE

WARRANTY IS VOID

PLATE GUARD CUTTER - DOES NOT OPEN OR CLOSE CORRECTLY:

▪

Thoroughly clean the contact surfaces of the guard.

HEAD - EXIT OF TOO MUCH OR TOO LITTLE GLUE:

▪

Check the air pressure of the glue unit.

▪

Make sure that the shutter of the head is free, passing the blade provided with the kit.

▪

Check that the lateral sizing holes are free, passing the steel wire supplied with the kit.

▪

Check that the injectors are working properly (must move back and forth with a 8-9 mm stroke).

▪

Verify that there is glue in the tank.

▪

Verify that the glue is not cured in the tank.

▪

Ensure that the fuel tap is open.

▪

Verify that the position of the inner side clamp is 0.15 tenths behind with respect to the thread
of the vice.

PRESS

▪

Book dented: clean the plates with suitable solvents and do not use abrasives.

▪

The edge is pinched: contact technical support.

▪

The book block is lined laterally: make sure you entered the correct thickness of the book.

▪

Clean the cutter rear contrast.

Summary of Contents for MB300 XL Pro





















































































Search results

Summary of Contents for MB300 XL Pro

Reviews:

Related manuals for MB300 XL Pro

Brands by name

Popular brands

Morgana MB300 XL Pro, Operator'S Manual

Search results

Summary of Contents for MB300 XL Pro

Reviews:

Related manuals for MB300 XL Pro

Brands by name

Popular brands