Morgana MB300 XL Pro Operator'S Manual Download Page 80

Page: 80 / 84

MB300 XL Pro

rev.0.2 ID03570

A22

Machine with Cleaner

When the machine is switched off the head is cleaned

using the automatic cycle of the cleaner. Use the load

cycle to load the glue. The cart does not work with this

alarm.

A23

Carry out PINS maintenance !!!

The head valves do not work correctly. Call the technical

support service.

A31

Book too thick detected

The thickness detected by the device is under 2mm or

over 50mm. (OPTIONAL)

A33

Remove book from vice

The vice asks for positioning, reset the alarm and press

the START button.

A34

Place book in vice

The START button was pressed without having inserted

the book

A35

Book presence photocell in vice

blocked

Clean the photocell and reflector and check obstacles.

A36

Blocked glue photocell

Clean the photocell and reflector and check obstacles.

A37

Jogger unit out of position

It appears when you want to make a book without

milling and the jogger unit is not set to 0.

A38

Cutter door not closed

Check the mobile protection of the cutter and if

necessary clean the guide beneath.

A39

Cutter unit out of position

Check the lever of the cutter is in the ON or OFF

position.

A40

Press up/down unit not in
position

Height adjustment of the press not in position Press
the START button.

A41

Remove book from press

A42

Pins sensor error

Call support, check the pins command cart is not

blocked or the sensor is working properly.

A43

Place cover

Position the cover or check the sensor is working.

A44

Glue photocell wrong reading

The photocell has two or more impulses, do not insert

two books or clean the vice.

A45

TUTORIAL NON COMPLETED Complete the TUTORIAL to continue.

A46

Lack of Air

The minimum pressure was not reached, check the

pneumatic power supply

A47

PLC battery flat

Call the technical support service.

A48

End of production

It appears when the number of copies set on the
counter is reached.

A49

Threshold not reached - Check

tank closure

The pressure set by the machine is not reached. It can

also happen that during the glue level control, check

there are no air leaks in the premelter.

A50

Closed premelter air valve

During glue level control, the machine identified the

premelter valve is closed or there is some blockage

that prevents pressure entering the tank.

A51

Low Glue Level

The machine cannot guarantee book production.

Summary of Contents for MB300 XL Pro





















































































Search results

Summary of Contents for MB300 XL Pro

Reviews:

Related manuals for MB300 XL Pro

Brands by name

Popular brands

Morgana MB300 XL Pro, Operator'S Manual

Search results

Summary of Contents for MB300 XL Pro

Reviews:

Related manuals for MB300 XL Pro

Brands by name

Popular brands