Moons' TSM24P User Manual Download Page 48

Page: 48 / 49

Rev. 1.0

0012072012

TSM24P User Manual

+86-400-820-9661

Because of the intense nature of serial communications required in host mode applications,

there is a serial communication Protocol (PR) command available that will adjust a drive’s

serial communications protocol to best fit an application. Typically this command is used when

configuring a drive and saved as part of the startup parameters. But it can be used at any time to

dynamically alter the serial communications.
The SCL Utility Software Manual contains the complete command listing as well as instructions on

connecting and configuring the TSM24P for use in SCL mode, using the Data Registers and the

Protocol command. It also contains detailed information on:
Host Serial Communications
Host Serial Connections
Alarm and Status Codes
Working with Inputs and Outputs
The Manual is available from the MOONS’ website at

http://www.moonsindustries.com/Products/

Drives/Software/.

under the SCL Utility download section.

Summary of Contents for TSM24P


















































Search results

Summary of Contents for TSM24P

Reviews:

Related manuals for TSM24P

Brands by name

Popular brands

Moons' TSM24P, User Manual

Search results

Summary of Contents for TSM24P

Reviews:

Related manuals for TSM24P

Brands by name

Popular brands