
Datum, Uhrzeit und Alarmstatus werden mit den Ka-
merabildern aufgezeichnet und bei der Wiedergabe
mit angezeigt.
Zur Rückkehr in die Betriebsart Live-Überwa-
chung nochmals die Taste
drücken.
B Vorschau (Wiedergabe der Bilder im Original-
Aufzeichnungsformat)
Bei Wahl dieser Funktion werden die Kamerabilder,
die über die Buchse VCR OUT (21) im Zeit-Multi-
plex-Verfahren aufgenommen wurden, im Original-
Aufzeichnungsformat, d. h. als codierte Einzelbild-
sequenzen, wiedergegeben.
Zuerst die SEL-Taste (12) und anschließend die
Taste
(10) drücken. Die LED über der Taste fängt
daraufhin an zu blinken. Auf dem Monitor wird das
am VCR IN (17) ankommende Signal, das codierte
Multiplex-Videosignal, dargestellt. Einzelne Kame-
rabilder lassen sich in dieser Betriebsart nicht ge-
zielt anwählen. Lediglich die Freeze-Taste
(9) er-
laubt das Einfrieren einzelner Bilder zur genaueren
Betrachtung.
Zur Rückkehr in die Betriebsart Live-Überwa-
chung nochmals die Taste
drücken.
6.1.3
Live-Aufnahme (Aufnahme einer ausge-
wählten Kamera im Vollbild-Format)
Diese Betriebsart dient dazu, die Aufnahme im Zeit-
Multiplex-Verfahren abzubrechen und stattdessen
nur das Bild eines Kamerakanals mit dem Videore-
corder aufzuzeichnen.
Zum Schalten in diese Betriebsart die LIVE-
REC.-Taste (14) drücken. Die LED neben der Taste
leuchtet. Anschließend über die entsprechende
Nummerntaste (15) die aufzunehmende Kamera
wählen. Die Kamera muß im Einstellungsmenü (sie-
he Kap. 8.6 „Menüpunkt 5: Kameras aufzeichnen“)
für die Aufnahme freigegeben sein („AN“) und tat-
sächlich ein Videosignal liefern, sonst kommt es
zum Abbruch der Live-Aufnahme-Funktion. Wurde
eine gültige Kameranummer gewählt, blinkt die LED
neben der LIVE REC.-Taste und alle 20 s ertönt ein
kurzer Signalton, wenn diese Funktion im Einstel-
lungsmenü aktiviert wurde. (Näheres zu den Einstel-
lungen im Kap. 8.6.)
Zur Beendigung der Live-Aufnahme und zur Rück-
kehr zur Video-Multiplex-Aufzeichnung nochmals
die LIVE REC.-Taste drücken.
6.2
Anzeigeformate wählen
Die Einstellungen der einzelnen Anzeigeformate
werden für die Betriebsarten Live-Überwachung und
Videorecorder-Wiedergabe separat dauerhaft ge-
speichert (außer im Zoom-Modus), so daß bei der
Anwahl eines Anzeigeformats automatisch die in der
jeweiligen Betriebsart zuletzt eingestellte Bildanord-
nung dargestellt wird.
6.2.1
Vollbild-Format
In diesem Format erscheint die gewählte Kamera
als Vollbild auf dem Hauptmonitor.
1) Um den Hauptmonitor in den Vollbild-Modus zu
schalten, die Taste
(1) drücken. Die LEDs über
der Taste
und über der Nummerntaste (15) der
gewählten Kamera leuchten. Mit jedem erneuten
Drücken der Taste
wechselt die Anzeige auf
die Kamera mit der nachfolgenden Nummer. Über
eine der Nummerntasten kann eine gewünschte
Kamera auch direkt ausgewählt werden.
2) Durch Drücken der Taste
(11) startet die auto-
matische Weiterschaltung (Sequenzschaltung)
der Kamera-Vollbilder. Die LED über der Taste
leuchtet. Näheres zu den Einstellungen für die
Sequenzschaltung in Kap. 8.4 „Menüpunkt 3: Se-
quenzschaltung einrichten“. Erneutes Drücken
der Taste
stoppt die Sequenzschaltung; die
LED erlischt.
6.2.2
Bild-im-Bild 1 mit einer Einblendung
Im Bild-im-Bild-Modus 1 wird eine Kamera im Voll-
bild gezeigt und eine weitere Kamera darin einge-
blendet in
1
/
9
-Größe des Vollbild-Formats.
1) Um auf den ersten Bild-im-Bild-Modus zu schal-
ten, die Taste
(2) drücken. Die LED über der
Taste leuchtet. Mit jedem erneuten Drücken der
Taste
wechselt die Einblendung auf die Kamera
mit der nachfolgenden Nummer. Zum Auswählen
der Kamera, die als Vollbild erscheinen soll, die
entsprechende Nummerntaste (15) drücken. Die
Kamera mit der nachfolgenden Nummer erscheint
im Vollbild eingeblendet.
Die Kameras für das Vollbild und die Einblen-
dung lassen sich auch direkt zuordnen. Dazu die
SEL-Taste (12) drücken; die LED darüber leuch-
tet. Jetzt über die Nummerntasten zuerst das
Vollbild und dann die Einblendung wählen. An-
schließend erlischt die LED über der SEL-Taste
wieder.
Vollbild und Einblendung lassen sich gegen-
einander austauschen. Dazu nacheinander die
SEL-Taste und die Taste
drücken.
2) Durch Drücken der Taste
(11) startet die auto-
matische Weiterschaltung (Sequenzschaltung)
für die Einblendung. Die LED über der Taste
leuchtet. Näheres zu den Einstellungen für die
Sequenzschaltung in Kap. 8.4 „Menüpunkt 3: Se-
quenzschaltung einrichten“. Erneutes Drücken
der Taste
stoppt die Sequenzschaltung; die
LED erlischt.
6.2.3
Bild-im-Bild 2 mit vier Einblendungen
Im Bild-im-Bild-Modus 2 wird eine Kamera im Voll-
bild gezeigt und vier weitere Kameras am unteren
Rand in je
1
/
16
-Größe des Vollbild-Formats darin ein-
geblendet.
1) Um auf den zweiten Bild-im-Bild-Modus zu schal-
ten, die Taste
(3) drücken. Die LED über der
Taste leuchtet. Mit jedem erneuten Drücken der
Taste
wechseln die Einblendungen auf die Ka-
meras mit den nachfolgenden Nummern. Zum
Auswählen der Kamera, die als Vollbild erschei-
nen soll, die entsprechende Nummerntaste (15)
drücken. Die Kameras mit den nachfolgenden
Nummern erscheinen im Vollbild eingeblendet.
Die Kameras für das Vollbild und die Einblen-
dungen lassen sich auch direkt zuordnen. Dazu
die SEL-Taste (12) drücken; die LED darüber
leuchtet. Jetzt über die Nummerntasten zuerst
das Vollbild und dann die Einblendungen wählen.
Anschließend erlischt die LED über der SEL-
Taste wieder. Sollen nicht allen Einblendungen
Kameras zugeordnet werden, den Vorgang durch
1
1
1
1
1
1
6.1.3
Live recording (recording of a selected
camera in full screen format)
This operating mode serves for breaking off the re-
cording in the time-multiplex technique and instead
recording only the picture of one camera channel
with the video recorder.
To switch to this operating mode, press button
LIVE REC. (14). The LED next to the button lights
up. Then select the camera to be recorded via the
corresponding numerical key (15). The camera must
be enabled for the recording (“ON”) in the setting
menu (see chapter 8.6 “Menu item 5: Cameras to
Record”) and really supply a video signal, otherwise
breaking off of the live recording function will result. If
a valid camera number has been selected, the LED
next to the LIVE REC. button blinks and every 20 s a
short signal sound can be heard in case this function
has been activated in the setting menu. (For further
information on the settings refer to chapter 8.6.)
To stop the live recording and to return to the
video multiplex recording, press the LIVE REC. but-
ton once again.
6.2
Selecting display formats
The settings of the individual display formats are
permanently memorized separately for the operat-
ing modes of live monitoring and video recorder re-
production (except for the zoom mode) so that when
selecting a display format, the picture arrangement
last adjusted in the respective operating mode is au-
tomatically shown.
6.2.1
Full screen format
In this format the selected camera is displayed as
full screen picture on the main monitor.
1) To switch the main monitor to the full screen
mode, press the button
(1). The LEDs above
the button
and above the numerical key (15) of
the selected camera light up. With each new
pressing of the button
the display changes to
the camera with the following number. Via one of
the numerical keys a desired camera can also
directly be selected.
2) By pressing the button
(11) the automatic se-
quential switching of the full screen pictures of
the cameras starts. The LED above the button
lights up. For further information on the settings
for the sequential switching refer to chapter 8.4
“Menu item 3: Sequence Setup”. Press the but-
ton
again to stop the sequential switching; the
LED extinguishes.
6.2.2
Picture-in-picture 1 with one insertion
In the picture-in-picture mode 1 one camera is shown
on the full screen and a further camera is inserted
into this picture in
1
/
9
size of the full screen format.
1) To switch to the first picture-in-picture mode,
press the button
(2). The LED above the but-
ton lights up. With each new pressing of the but-
ton
the insertion changes to the camera with
the following number. To select the camera,
which is to be displayed as full screen picture,
press the corresponding numerical key (15). The
camera with the following number appears as
insertion in the full screen picture.
The cameras for the full screen picture and the
insertion can also be assigned directly. For this
press the SEL button (12); the LED above it lights
up. Now select the full screen picture first and then
the insertion via the numerical keys. Then the LED
above the SEL button extinguishes again.
Full screen picture and insertion can mutually
be exchanged. For this press the SEL button and
the button
successively.
2) By pressing the button
(11) the automatic se-
quential switching for the insertion starts. The
LED above the button
lights up. For further
information on the settings for the sequential
switching refer to chapter 8.4 “Menu item 3: Se-
quence Setup”. Press the button
again to stop
the sequential switching; the LED extinguishes.
6.2.3
Picture-in-picture 2 with four insertions
In the picture-in-picture mode 2 one camera is dis-
played on the full screen and four further cameras
are inserted in this picture at the lower edge, each in
1
/
16
size of the full screen format.
1) To switch to the second picture-in-picture mode,
press the button
(3). The LED above the but-
ton lights up. With each new pressing of the but-
ton
the insertions change to the cameras with
the following numbers. To select the camera,
which is to be displayed as full screen picture,
press the corresponding numerical key (15). The
cameras with the following numbers appear as
insertions in the full screen picture.
The cameras for the full screen picture and
the insertions can also directly be assigned. For
this press the SEL button (12); the LED above it
lights up. Now first select the full screen picture
and then the insertions via the numerical keys.
Then the LED above the SEL button extinguishes
again. In case not all insertions are to be as-
signed to cameras, break off the procedure by
pressing the SEL button; the LED above the SEL
button extinguishes.
The full screen picture and the first insertion
(left) can mutually be exchanged. For this press
the SEL button and the button
successively.
2) By pressing the button
(11) the automatic se-
quential switching for the last insertion (right)
starts. The LED above the button
lights up. For
further information on the settings for the sequen-
tial switching refer to chapter 8.4 “Menu item 3:
Sequence Setup”. Press button
again to stop
the sequential switching; the LED extinguishes.
6.2.4
Multiple picture 2 x 2
In the display format 2 x 2 four camera pictures are
shown, each in
1
/
4
size of the full screen format.
1) To select the display format 2 x 2, press the but-
ton
(4). The LED above the button lights up.
With each new pressing of the button
, the pic-
tures change to the four cameras which, accord-
ing to their numbers, follow the camera last
shown in the lower right partial picture. If a cam-
era is selected via one of the numerical keys (15),
it appears in the left upper partial picture. The
cameras with the following numbers are consecu-
tively displayed in the remaining partial pictures.
The cameras can also directly be assigned to
1
1
1
1
1
1
1
1
1
8
GB
D
A
CH