189
2009
K
night
Electrical Sy
stems - Chassis - 9
5. ODOMETER:
Displays total mileage.
6. FUEL:
Fuel gauge registers approximate
fuel tank level when ignition switch is
in the run position.
NOTE
Fuel mileage varies with driving style
and road conditions. Always average
more than one tankful to obtain a more
accurate figure. The diesel generator
uses fuel from main tank and will affect
fuel mileage figures. Diesel generators
will not operate below ¼ tank to ensure
there is enough fuel to run main engine.
7. TRANS TEMP:
Shows approximate
temperature of the transmission fluid.
DO NOT
let the transmission cooler oil
temperature exceed OEM specifications.
If excess temperature is indicated, stop
the motorhome and shift to neutral.
Accelerate the engine at 1200 to 1500
RPM and allow temperature to return to
normal.
8./9. AIR PRESSURE GAUGE:
Uses two
needles to indicate air system pressures.
One needle indicates air pressure of the
front air tank. The other needle indicates
air pressure of the rear air tank. The
normal air system operating pressures
are 115 to 130 psi. These air pressures
are preset at the factory. If a problem
occurs with either air system not
maintaining normal operating pressure,
it is an indication of a malfunction in
the air system. Use caution and stop
the motorhome in a safe area. Contact a
qualified technician immediately.
10. LCD DISPLAY:
The LCD displays
chassis data and fault codes. A ten
button controller is located on the dash.
Press the up and down arrows to scroll
through menus, and press the enter
button to select items.
The LCD display will show the following
warnings:
Eng Comm Failure
ABS Comm Failure
Trans Comm Failure
Low Oil Pressure
High Trans Temp
High Coolant Temp
Low/High Battery
Low Air Pressure – Front
Low Air Pressure – Rear
Low Fuel Level
Engine Not Running
Low Coolant Level
Alt Fail
Turn Signal
- For “Turn Signal” to display the
motorhome must be driven at least
one mile with turn signal activated
before warning appears.
How to Adjust Screen Contrast:
1. Press DIAG button on LCD
Controller.
2. Arrow down to 4 – Ins. Diag. Press
enter.
3. Arrow down to 5-Contrast. Press
enter.
4. Use arrow buttons to select value
desired. 40 is the default value.
5. Press MAIN button on LCD
Controller to exit.
NOTE
Layouts may vary with difference in
models or options.
LCD Controller (Optional)
Main
– Press at any time to return to the
main screen. The main screen displays
outside temperature, chassis battery voltage
and odometer.
Trip
– Press to view Trip menu. Use the up
or down arrow to highlight a trip, and press
the Enter button to view trip information.
Trip information includes average speed,
distance traveled, trip time and fuel used.
Fuel
– Press to display average miles per
gallon, instantaneous miles per gallon, and
fuel used. Hold the reset button for five
seconds to clear.
Temp
– Press to view outside, basement,
transmission and engine coolant temperature.
Diag
– Press to view engine, transmission,
ABS, and LCD diagnostic menu. Use the up
and down arrow to highlight an option from
the menu. Press the Enter button to view
diagnostic information and options.
LCD Controller
080515f
Summary of Contents for 2009 Knight
