13
2009
K
night
W
ater Sy
stems - 6
Press either button once to add water,
run motor and return to normal use.
Programming the Water Level
The water level in the
bowl can be programmed.
The minimum
recommended refill level
is ½" above the bowl
outfall hole. The opening
in the bowl is the outfall
hole. After changing
water source from municipal to pump,
resetting water may be necessary. To program
the water level perform the following steps.
Press both buttons and hold.
LEDs will flash indicating the toilet is
in program mode.
As water enters the bowl, release
fingers from buttons to set the level of
standing water in the bowl. The level
remains constant after each flush until
it is changed.
Holding Tank Level Sensors
The toilet system has tank level sensors
mounted on the outside of the black tank.
On the bathroom
control panel is a
small water icon
located in the
bottom right corner.
The following
information pertains
to that water icon.
Water Icon Not Lighted:
Toilet system is
Off, in sleep mode or not receiving power.
Water Icon Lighted Green:
Toilet system is
On and the holding tank is between empty and
half full.
Water Icon Lighted Yellow:
Toilet system
is On and the holding tank is at least half full.
Water Icon Lighted Red:
Toilet system is
On and the holding tank is full.
Full Tank Lockout:
For the safety of the
system, the toilet will not flush when the
system senses a full tank. This occurs when the
Water Icon is red.
Emergency Override
If the tank is full
(Water Icon is red) and an emergency flush is
needed do the following:
Press and hold either flush button for 6
seconds to flush toilet.
WARNING
Drain the black tank. If the black
tank is not drained, flushing will cause
overfilling of the black waste tank and
system back up. The diagnostic LED
warning icon will flash.
LED Sleep Mode:
To save power
consumption when not in use, an automatic
LED sleep mode is programmed on this
control panel. If the toilet is not used for 8
hours, the keypad LED lights will go out.
The press of any button will start a flush and
reactivate backlighting.
Toilet Shut-Off Valve:
A shut-off valve
is
located behind the toilet. In
the event of an emergency
the water line that leads into
the toilet can be shut off.
Cleaning
Regularly clean the toilet for maximum
sanitation and operational efficiency. Clean the
toilet bowl with a mild bathroom cleaner.
DO
NOT
use chlorine or caustic chemicals, such
as drain opening types, as they will damage the
seals.
Clean out the system by flushing several
gallons of fresh water through with one cup
of dry laundry detergent. Add odor control
deodorant, in the amount specified for your
holding tank capacity, after cleaning and every
few days during use.
POISON
Most chemical mixtures for holding
tank odor control are poisonous.
Follow the product manufacturer’s
directions and warnings when using
any holding tank additive.
Maintenance
To find leaks, check behind or under toilet.
Take four or five sheets of toilet tissue and
wipe all the water line connections. Start at the
top of the unit and work downward. When the
tissue comes in contact with leaking water it
immediately changes texture.
040466c
040466d
040631
Toilet
Shut-Off
Valve
Summary of Contents for 2009 Knight
