r = ramp value, can be set on digits 12 – 16 and
corresponds with temperature change speed
in °C/min max. value is +3.2 °C/min, when
T0 < T1, or T1 > T2 If r = 00.0, no ramp
active! (The numerical value of the ramp has
an orientation character, the real speed can
be affected by the amount of goods in the
chamber and maximum speed of temperature
change may not be met, taking the limited
heating power into account)
t = time available in position
¹
(00hr:00min –
9999 hr), at T2 the dwell time can be
unlimited
c = cycles shown in position
¹
, digits 12 – 13 on
LCD (available only at T2, if the dwell time is
unlimited) Possible number of cycles is 2 to
9999 (eventually ∞- which is the next position
after 99).
The value of cycle number is a global value that
does not relate to individual segments, it relates
to the complete programmed sequence. It can
be displayed while displaying any segment on
the display, however it does not concern only
the displayed segment, but the whole sequence!
minimum number of cycles is 1. If only one cycle
is chosen, the programme runs as if it has been
switched on without cycles.
The program can be started by depressing
STArT
; no matter which segment is shown on
the display, the program always runs from the
segment 0 or 1, if the time of the zero segment
is zero. For successful inserting of the cycling
process into an already started process it is
essential that at the moment of the start “cXX” is
shown on the display, where XX is the number
of intended runs of the whole sequence. E.g.
number two means, that the sequence is carried
out and then repeated completely, i.e. it runs
twice around. If “cXX” is not shown on the display
at the moment of the
STArT
and there is shown
data on time or on the ramp of the actually
displayed program instead, the whole sequence
runs once and is not repeated, i.e. there are no
cycles.
4.5.2
SET
THE
SEGMENT
FOR
T
1
4.5.2.1
SET
TEMPERATURE
T
1
Put cursor to the position Program and switch
to P4. By pressing ◄► place the cursor on the
graph and make sure that T1 (/¯\_) is activated. If
not, activate it with buttons ▲.
Change to the position of °C - temperature setting
- and set the temperature.
4.4.3.3
P
3
AND
THIRD
SEGMENT
IN
THE
GRAPH
ARE
ACTIVE
The preset temperature has been reached. If the
procedure duration is unlimited, time passed is
displayed. If the procedure duration is limited,
time remaining till the end is displayed. after the
programme ends, temperature in the chamber
and the text “End” are displayed. Programme
end indication and temperature in the chamber
disappear after pressing any panel key.
4.4.4
INFORMATION
ON
THE
SET
PARAMETERS
DURING
OPERATION
OF
THE
UNIT
See item 4.2.4.
4.4.5
STOP
P3
Press
STArT/STOp
.
4.5
PROGRAM
P4
With 2 temperature levels T1 and T2, with a
controlled speed of the temperature change
(ramps) and with cycling.
P4 =
T1
T2
operates at 2 temperature levels T1 and T2, the
dwell time on the level T1 is limited, on the level
T2 can be limited or unlimited.
4.5.1
SET
P
4
Index: T0 = initial chamber temperature
T1 = temperature level 1
T2 = temperature level 2
Digit 11 on LCD = (placed between temperature
and dwell time values), shows the following
information:
LSI_K_np_en 1206_mmm_V2.08_B2V
13
Instructions for use
Program Segment
°C
RH
5 6
* 3
//
–
°C
°C
°C .
1
0
0
h
h
: min
=
=
/
–
= druhý segment
segment 3
