"I FEEL..." Auto Operation
In the mode of "I FEEL..." Auto Operation, one press of the button enables the room condition to reach optimum status.
When starting "I FEEL..." Auto Operation
■
Press button.
At the time of displaying (Auto Operation), the air conditioner is automatically controlled to the optimum temperature.
When stopping
■
Press button
About 15 minutes after the start of operation:
If you feel too hot:
If you feel too cold:
■
Press button to increase the temperature.
Each press of the button increases the temperature by about 1
℃.
At the time of not displaying
(Auto Operation), please press
button to set Auto Operation mode.
Each press of the button enables the unit to change operation mode following the order of
(Auto Operation)
→
(Cooling)
→
(Dry)
→
(Heating)
→
(Fan).
Auto Operation mode
Auto Operation
The operation mode is automatically set to Cooling, Dry or heating based on the room temperature at initial operation. However, if the unit
operates again within 2 hours after stopping, it will operate following the same set points with the previous operation. Once the set points are set,
the operation will not vary with the room temperature. If you don’t like the set points, you can press
button, then select proper set points.
Set points for "I FEEL..." Auto Operation
Note:
■
Press
button to decrease the temperature.
Each press of the button decreases the temperature by about 1
℃
Cooling: When the room temperature is 2
℃
higher than the set temperature, the latter will not change. Because the air conditioner is operating
to reach the target (set point) temperature. Meanwhile, please wait for room temperature to decrease to the temperature around the set one
(+2
℃
) , then you can change the set temperature.
Heating: When the room temperature is 2
℃
lower than the set temperature, the latter will not change. Because the air conditioner is operating
to reach the target (set point) temperature. Meanwhile, please wait for room temperature to increase to the temperature around the set one
(+2
℃
) , then you can change the set temperature.
32
Room temperature at initial operation
Over 25
℃
Below 25
℃
Below 23
℃
Operation mode
Cooling
Dry
Heating
Target temperature (initial status)
About 24
℃
-
About 26
℃
Summary of Contents for MSZ-YK09VA-H1
