Mitsubishi MR-JE-100B, Instruction Manual, Page: 19 / 294

1. FUNCTIONS AND CONFIGURATION
1 - 4
1.3 Servo amplifier standard specifications
Model: MR-JE- 10B 20B 40B 70B 100B 200B 300B
Output
Rated voltage 3-phase 170 V AC
Rated current [A] 1.1 1.5 2.8 5.8 6.0 11.0 11.0
Power supply
input
Voltage/frequency
3-phase or 1-phase 200 V AC to 240 V AC, 50
Hz/60 Hz
3-phase or 1-phase 200
V AC to 240 V AC, 50
Hz/60 Hz (Note 5)
3-phase
200 V AC
to 240 V
AC, 50
Hz/60 Hz
Rated current
(Note 1)
[A] 0.9 1.5 2.6 3.8 5.0 10.5 14.0
Permissible voltage
fluctuation
3-phase or 1-phase 170 V AC to 264 V AC
3-phase or 1-phase 170
V AC to 264 V AC
(Note 5)
3-phase
170 V AC
to 264 V
AC
Permissible frequency
fluctuation
Within ±5%
Power supply
capacity
[kVA] Refer to section 10.2.
Inrush current [A] Refer to section 10.5.
Interface
power supply
Voltage 24 V DC ± 10%
Current capacity [A] 0.3 (Note 2)
Control method Sine-wave PWM control, current control method
Dynamic brake Built-in
SSCNET III/H communication cycle
(Note 3)
0.444 ms, 0.888 ms
Communication function USB: Connection to a personal computer or others (MR Configurator2-compatible)
Protective functions
Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic thermal),
servo motor overheat protection, encoder error protection, regenerative error protection,
undervoltage protection, instantaneous power failure protection, overspeed protection, and
error excessive protection
Compliance
with global
standards
CE marking
LVD: EN 61800-5-1
EMC: EN 61800-3
UL standard UL 508C
Structure (IP rating) Natural cooling, open (IP20)
Force cooling, open
(IP20)
Close
mounting
(Note 4)
3-phase power supply
input
Possible
1-phase power supply
input
Possible Impossible
Ambient
temperature
Operation 0 °C to 55 °C (non-freezing)
Storage -20 °C to 65 °C (non-freezing)
Ambient
humidity
Operation
5 %RH to 90 %RH (non-condensing)
Environment Storage
Ambience Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust
Altitude 2000 m or less above sea level (Note 6)
Vibration resistance 5.9 m/s
2
, at 10 Hz to 55 Hz (directions of X, Y and Z axes)
Mass [kg] 0.8 1.5 2.1
Note 1. This value is applicable when a 3-phase power supply is used.
2. The current capacity 0.3 A is applicable when all I/O signals are used. The current capacity can be decreased by reducing the
number of I/O points. For the servo amplifiers manufactured in April 2016 or earlier (or manufactured in China in May 2016 or
earlier), the current capacity 0.1 A is applicable.
3. The communication cycle depends on the controller specifications and the number of axes connected.
4. When closely mounting the servo amplifiers, operate them at the ambient temperature of 0 °C to 45 °C or at 75% or smaller
effective load ratio.
5. When using 1-phase 200 V AC to 240 V AC power supply, operate the servo amplifier at 75% or smaller effective load ratio.
6. Follow the restrictions in section 2.7 when using this product at altitude exceeding 1000 m and up to 2000 m above sea level.