H2i-R2-12
PURY-HP-T(S)KMU,-Y(S)KMU (September 2014)
© 2014 Mitsubishi Electric US, Inc.
2. EXTERNAL DIMENSIONS
2 - 253
2. EXTERNAL DIMENSIONS
DATA U10
OUTDOOR UNITS
H
2i
R
2
PURY-HP72, 96TKMU-A-H(-BS)
Unit : mm(in)
●In case of single installation
1. Required space around the unit
2
When the height of the walls on the front,back or on the sides<H>
exceeds the wall height limit as defined below
add the height that exceeds the height limit <h> to the figures that
are marked with an asterisk.
1
Secure enough space around the unit as shown in the figure below
.
2. Foundation work
W
all <H>
Front
Front
Front
Front
Front
Front
Wall <H>
Wall<H>
Front
<Unit:mm(in)>
<T
o be left open>
W
all <H>
Front
<T
o be left open>
W
all <H>
W
all <H>
W
all <H>
W
all <H>
<T
o be left open>
W
all <H>
W
all <H>
Front
Front
<Unit:mm(in)>
1
When multiple units are installed adjacent to each other
, secure enough space to allow
for air circulation and walkway between groups of units as shown in the figures below
.
2
At least two sides must be left open.
3
As with the single installation, add the height that exceeds the height limit<h>
to the figures that are marked with an asterisk.
4
If there is a wall at both the front and the rear of the unit, install up to six units
consecutively in the side direction and provide a space of 1000mm or more as inlet space/
passage space for each six units.
●In case of collective installation
1
Take into consideration the surface strength, water drainage route,
piping route, and wiring route when preparing the installation site.
<Note that the drain water comes out of the unit during operation.>
2
Build the foundation in such way that the corner of the installation leg is
securely supported as shown in the right figure.(Fig.A)
When using a rubber isolating cushion, please ensure it is large enough
to cover the entire width of each of the unit's legs.
3
The protrusion length of the anchor bolt must not exceed 30mm(1-3/16).(Fig.A)
4
Use four fixing plates as shown in the right figure <field supply required>
when using post-installed anchor bolts.(Fig.B)
5
To prevent small animals and water and snow from entering the unit and damaging its parts,
close the gap around the edges of through holes for pipes and wires with
filler plates <field supply required>.
6
When the pipes or cables are routed at the bottom of the unit,
make sure that the through hole at the base of the unit does not get blocked
with the installation base.
7
Refer to the Installation Manual when installing units on an installation base.
(19-11/16)
(1-3/16)
(35-7/16)
(11-13/16)
(35-7/16)
(11-13/16)
(11-13/16)
(19/32)
(17-23/32)
(17-23/32)
(39-3/8)
(17-23/32)
(17-23/32)
(17-23/32)
(3-15/16)
(3-15/16)
(1-3/16)
(11-13/16)
(3-15/16)
(17-23/32)
(17-23/32)
(1-31/32)
(1-31/32)
(3-15/16)
(17-23/32)
(19/32)
(19/32)
(11-13/16)
(17-23/32)
<To be left open>
<To be left open>
<To be left open>
<To be left open>
<To be left open>
<To be left open>
<To be left open>
Front
M10 anchor bolt <field supply required>
Fixing plate <field supply required>
Front
<T
op view>
<T
op view>
Front
<Side view>
•
With a space of at least
300mm(1
1-13/16) to the wall on
the back of the unit
<W
all height limit>
Front
: Up to the unit height
Back
: Up to 500mm(19-1
1/16) from
the unit bottom
Side
: Up to the unit height
Fig.A
Fig.B
Unit height
500
900 min.
300 min.*
1000 min.*
300 min.*
300 min.*
900 min.
15 min.*
450 min.
450 min.
100 min.*
450 min.
450 min.
450 min.*
100 min.
450 min.*
100 min.*
30 min.
300 min.*
450 min.*
100 min.*
450 min.*
450 min.*
300 min.*
15 min.*
15 min.*
50 min.*
50 min.*
H
h
h
H
30mm max.
•
With a space of at least
100mm(3-15/16) to the wall on
the back of the unit
