Mitsubishi Electric A800-E Instruction Manual Download Page 3 | Manualshive

Page: 3 / 84

background image

Ethernet communication overview

2

INTRODUCTION

1

INTRODUCTION

1.1

Ethernet communication overview

The FR-A800-E/FR-F800-E inverter is equipped with an Ethernet board. Communication with network devices can be made
via Ethernet by connecting an Ethernet cable to the Ethernet connector on the Ethernet board.



Precautions for Ethernet communication

• In order to protect the inverter and the system against unauthorized access by external systems via network, take security

measures including firewall settings.

• Depending on the network environment, the inverter may not operate as intended due to delays or disconnection in

communication. Carefully consider the conditions and safety for the inverter on site.



Abbreviations



The solution enables seamless sensor control using a programmable controller, GOT, and other devices. The iQSS contributes to the reduction
in the total cost from development to maintenance of production equipment.



Trademarks

• Ethernet is a registered trademark of Fuji Xerox Corporation.
• MODBUS is a registered trademark of SCHNEIDER ELECTRIC USA, INC.

Abbreviation / generic name

Description

DU

Operation panel (FR-DU08)

Operation panel

Operation panel (FR-DU08) and LCD operation panel (FR-LU08)

Parameter unit

Parameter unit (FR-PU07)

PU

Operation panel and parameter unit

Inverter

Mitsubishi FR-A800-E/FR-F800-E inverter

Ethernet board

Ethernet communication board (FR-A8ETH)

Pr.

Parameter number (Number assigned to function)

SLMP

Seamless Message Protocol

iQSS

Mitsubishi iQ Sensor Solution

TCP/IP

Transmission Control Protocol / Internet Protocol

UDP/IP

User Datagram Protocol / Internet Protocol

Hub

Inverter

Inverter

Personal computer
(FR Configurator2)

Programmable controller

GOT

«
1
2
3
4
5
...
»

Summary of Contents for A800-E





















































































Reviews:

No comments

Related manuals for A800-E

Brand: QUAD Pages: 2

Brand: hc-cargo Pages: 38

Brand: ATEN Pages: 2

Brand: Patton electronics Pages: 7

Brand: Sencore Pages: 126

Brand: nedis Pages: 28

VideoExpress Converter

Brand: Miglia Pages: 12

Adaptatone 5530M-485 Series

Brand: Edwards Signaling Pages: 13

DEMO CIRCUIT 1672A

Brand: Linear Technology Pages: 13

Brand: D&H Pages: 106

Brand: OLIJU Pages: 20

Brand: Sencore Pages: 203

Brand: Delta Electronics Pages: 2

Brand: RS Pages: 8

Brand: Ensemble Designs Pages: 24

Brand: AJA Pages: 43

CONVERTEON AT-CM201

Brand: Allied Telesis Pages: 3

Brand: FireBird Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands