Mitsubishi Electric A800-E Instruction Manual Download Page 75

Page: 75 / 84

Inverter-to-inverter link function

PARAMETER



Special register (master)



Special register (slave)



Troubleshooting

SD1461

Communication status of inverter-to-
inverter link

The communication status of the slaves in the inverter-to-inverter
link is stored.
(In the slave inverter, only its own communication status is
indicated.)

Device No.

Name

Description

SD1470 to SD1477

Inverter-to-inverter link receive data 1 to 8 (slave 1)

Data 1 to 8 received from slave 1

SD1478 to SD1485

Inverter-to-inverter link send data 1 to 8 (slave 1)

Data 1 to 8 sent to slave 1

SD1486 to SD1493

Inverter-to-inverter link receive data 1 to 8 (slave 2)

Data 1 to 8 received from slave 2

SD1494 to SD1501

Inverter-to-inverter link send data 1 to 8 (slave 2)

Data 1 to 8 sent to slave 2

SD1502 to SD1509

Inverter-to-inverter link receive data 1 to 8 (slave 3)

Data 1 to 8 received from slave 3

SD1510 to SD1517

Inverter-to-inverter link send data 1 to 8 (slave 3)

Data 1 to 8 sent to slave 3

SD1518 to SD1525

Inverter-to-inverter link receive data 1 to 8 (slave 4)

Data 1 to 8 received from slave 4

SD1526 to SD1533

Inverter-to-inverter link send data 1 to 8 (slave 4)

Data 1 to 8 sent to slave 4

SD1534 to SD1541

Inverter-to-inverter link receive data 1 to 8 (slave 5)

Data 1 to 8 received from slave 5

SD1542 to SD1549

Inverter-to-inverter link send data 1 to 8 (slave 5)

Data 1 to 8 sent to slave 5

Device No.

Name

Description

SD1470 to SD1477

Inverter-to-inverter link receive data 1 to 8 (master)

Receive data 1 to 8 from master

SD1478 to SD1485

Inverter-to-inverter link send data 1 to 8 (master)

Send data 1 to 8 to master

SD1486 to SD1549

For manufacturer setting. Do not set.

Condition

Possible cause

Countermeasure

Communication is not
established.

The same station number is assigned to multiple
inverters.

Set

Pr.1124

correctly.

The station numbers are not consecutive.

Set

Pr.1124

so that the station numbers are

consecutive.

The specified number of inverters in the system is
not correct.
(

Pr.1124

is set to a value equal to or larger than

the value set in

Pr.1125

Set

Pr.1125

correctly.

The connection is half-duplex.

Use full-duplex connection. (When

Pr.1426 Link

speed and duplex mode selection

= "0 (initial

value)", check that the hub and the Ethernet cable
are compatible with full-duplex connection.)

The inverter is not reset after

Pr.1124

and

Pr.1125

are set.

Reset the inverter.

A command sent by the master
is not applied to a slave.

The PLC function is disabled.

Set a value other than "0" in

Pr.414

to enable the

PLC function.

Device No.

Name

Description

b15

Bit

Target station

Description

Slave 1

0: The link is not established.
1: The link is established.

Slave 2

Slave 3

Slave 4

Slave 5

Summary of Contents for A800-E





















































































Search results

Summary of Contents for A800-E

Reviews:

Related manuals for A800-E

Brands by name

Popular brands

Mitsubishi Electric A800-E, Instruction Manual

Search results

Summary of Contents for A800-E

Reviews:

Related manuals for A800-E

Brands by name

Popular brands