Mitel UC360 Administration Manual Download Page 34 | Manualshive

Page: 34 / 141

background image

UC360 Administration Guide

18

SIP Proxy Server

The IP address (IPv4) of the SIP Proxy server.

Mac Address

The hardware address associated with the network interface on the UC360.

Phone IP Address

The UC360 requires an IP address. This is an IPv4 address and it is recommended that the
address selected be in the same subnet as the local ethernet camera.

Default Gateway IP Address

This is the IP address (IPv4) of the gateway (or default router) that allows access to other
subnets.

Subnet Mask

Consult with the network administrator as to how this should be set.

VLAN ID

This field is used by the administrator to set the VLAN ID. The default setting for this field is no
value (blank).

Note: If a VLAN ID is not entered into this field, then the L2 priority settings will not take effect.

L2 Priority Voice

This screen allows the administrator to set the L2 priority for Voice packets. A value of 6 is
recommended. For further details, see section on UC360 Quality of Service Settings.

L2 Priority Signaling

This screen allows the administrator to set the L2 priority for Signaling packets. A value of 3 is
recommended. For further details, see section on UC360 Quality of Service Settings.

L2 Priority Multimedia

This screen allows the administrator to set the L2 priority for Multimedia packets. A value of 4
is recommended. For further details, see section on UC360 Quality of Service Settings.

DSCP Voice

This screen allows the administrator to set the L3 priority for Voice packets. A value of 46 is
recommended. For further details, see section on UC360 Quality of Service Settings.

«
...
32
33
34
35
36
...
»

Summary of Contents for UC360














































































































































Reviews:

No comments

Related manuals for UC360

Brand: T-Mobile Pages: 2

Brand: 2N Pages: 8

Brand: 2N Pages: 83

Brand: Eaton Pages: 44

SB3.0-1SP-US-40

Brand: SMA Pages: 17

Smartphone E-11

Brand: Etisalat Pages: 75

Brand: TCL Pages: 74

Brand: SoftBank Pages: 36

Brand: Mircom Pages: 39

Brand: Trikdis Pages: 22

WeMove Discovery

Brand: NGM Pages: 11

Brand: Mircom Pages: 149

media:scape mini

Brand: Steelcase Pages: 7

Brand: Samsung Pages: 144

Brand: Samsung Pages: 160

Brand: Samsung Pages: 162

Brand: Samsung Pages: 186

Brand: Samsung Pages: 144

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands