Mitel UC360 Administration Manual Download Page 43 | Manualshive

Page: 43 / 141

background image

UC360 Configuration

27

Video Settings

Video Settings allow you to adjust video bandwidth parameters for both the uplink and downlink
LAN connections. The video settings menu also allows you to enable or disable the Dynamic
Bandwidth Allocation (DBA) capability introduced in Release 2.0.

DBA is an algorithm the UC360 uses to reduce packet loss on a congested communication
link. DBA will lower the UC360's transmitted bit rate according to the packet loss feedback it
receives from the remote end, the end goal being that a reduction in the transmission rate
should alleviate congestion and packet loss.

DBA relies on the RTCP protocol. At the time of writing, the MiVoice Border Gateway does not
support the RTCP protocol. As a result, if the UC360 is connected to an MiVoice Border
Gateway, you should disable the DBA feature on the UC360.

1.

Press Settings

.

2.

Press Advanced.

3.

Press System Settings.

4.

Select Video Settings.

5.

Select the bandwidth for the video quality: High, Medium, or Low.

6.

Enable Dynamic Bandwidth Allocation, if desired.

7.

Click Save.

See the

UC360 Engineering Guidelines

for details on Dynamic Bandwidth Allocation.

«
...
41
42
43
44
45
...
»

Summary of Contents for UC360














































































































































Reviews:

No comments

Related manuals for UC360

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 142

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 68

Brand: Unitech Pages: 81

One Touch 997D Ultra

Brand: Alcatel Pages: 21

8700 - 8707H SMARTPHONE

Brand: Blackberry Pages: 48

Brand: Sagem Pages: 70

IntelliGate 2025

Brand: Aastra Pages: 71

Brand: Sonim Pages: 1

Brand: Brava Pages: 97

Brand: Dotel Pages: 37

Brand: Ericsson Pages: 77

Brand: BENQ-SIEMENS Pages: 114

Brand: Alcatel Pages: 51

Brand: Vantage Hearth Pages: 2

Talk-N-Trace TM-110

Brand: JDS Uniphase Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands