Mitel UC360 Administration Manual Download Page 138

Page: 138 / 141

UC360 Administration Guide

122

Backup Import/Export

HTTP Import

Configuration

<http_cfg ServerUrl=”[HTTP SERVER URL – can include port & path]”

HTTP Server Address

TrustAllHosts="[0:disable|1:enable]"></http_cfg>

Statically configured address
overrides any value from DHCP

Upgrade System SW

Software HTTP Server

Address

<http_download>[HTTP SERVER IP PORTION]</http_download>

<http_port>[HTTP SERVER PORT NUMBER]</httpport>

httpport not required. port
number default is 80. A value will
only be provided if explicitly set
in the port part of the HTTP URL.
Conversely having no port set
here means the default port (80)
is used.

Auto Upgrade

<http_upgrade>[0 disabled|1:upgrade on|2:upgrade auto]></http_upgrade>

N.B. UC360, will check on
reboot as well.

Auto Polling

<firmware_abs_enable>[0:disabled|1:enabled]</firmware_abs_enable>

User Confirmation

<http_upgrade_user_confirm>[0 disabled|1:upgrade on]></http_upgrade>

upgrade auto will not prompt
user

Upgrade Time

<firmware_abs_timer_hr>[24 HOUR FORMAT HOUR]</firmware_abs_timer_hr>

<firmware_abs_timer_min>[MINUTE]</firmware_abs_timer_min>

Debug Settings

Debugging (Debug Logging)

Debugging Level

Verbose(2), debug(3), info(4),
warn(5), error(6)

Kernel Messages

Debug Logs Size

Automatic Ethernet Trace (Congestion)

Manual Ethernet Trace (User Button Enable)

Development

Ethernet Debugging

eXoSIP Log Level

Debug DSP

Legacy Interop Mode

Always mirror primary to HDMI

Summary of Contents for UC360














































































































































Search results

Summary of Contents for UC360

Reviews:

Related manuals for UC360

Brands by name

Popular brands

Mitel UC360, Administration Manual

Search results

Summary of Contents for UC360

Reviews:

Related manuals for UC360

Brands by name

Popular brands