Miranda DENSITE XVP-1801 Manual To Installation And Operation Download Page 55 | Manualshive

Page: 55 / 65

Miranda DENSITE XVP-1801 Manual To Installation And Operation Download Page 55

GUIDE TO INSTALLATION AND OPERATION

XVP-1801 |

51

3.5.16 The

Info

group

The top two lines in this panel identify the model of
this XVP-1801, and the rear panel that is currently
installed.

When the XVP-1801 is included in an iControl
environment, certain information about the card
should be available to the iControl system. The user
can enter labels and comments that will make this
card easy to identify in a complex setup. This
information is entered into data boxes in the Info
control panel.

Label:

type the label that is shown for this
XVP-1801 when it appears in iControl
applications

Short Label type the short-form label that iControl

uses in some cases (8 characters)

Source ID

type a descriptive name for this XVP-
1801

Comments: type any desired text

The remaining data boxes show manufacturing information about this card.

Three buttons in the panel give access to other information.

•

Details…: Reports the Firmware version, service

version, and panel version for this card

•

Advanced…: Shows the Miranda LongID for this card.

The Miranda LongID is the address of this XVP-1801in
the iControl network.

Figure 3.43

Details window

Figure 3.44

Advanced window

Figure 3.42

Info group

«
...
53
54
55
56
57
...
»

Summary of Contents for DENSITE XVP-1801


































































Reviews:

No comments