manualshive.com logo in svg

Miranda DENSITE XVP-1801, Manual To Installation And Operation, Page: 41 / 65

Share
Download
Miranda DENSITE XVP-1801 Manual To Installation And Operation Download Page 41

GUIDE TO INSTALLATION AND OPERATION 

XVP-1801  |  

37

  

 

 

 Figure 

3.21 

 LtRt Surround Sound downmixer 

 

 

 

 Figure 

3.22 

 LoRo Stereo downmixer

 

 
 

•

  Normalization:  the downmix levels can be normalized to provide normalized levels according to the 

downmix levels used in manual mode or AUTO mode.  

 
 

Status

 tab 

The Status tab reports the type of audio present at 
the input and the Dolby-E alignment. 
 
Audio Type Status: 
 

•

 

PCM – the audio channel carries PCM 
audio (orange) 

 

•

 

Dolby E – the audio channel carries Dolby 
E encoded audio (blue) 

 

•

 

AC3 – the audio channel carries Dolby 
Digital (AC-3) encoded audio (violet) 

 

•

 

NPCM – the audio channel carries non-
PCM other than Dolby E or Dolby Digital 
(AC-3) (yellow). 

 
 
 

+

+

+

+

–

+

+

+

Surround

Level

L

C

R

LFE

Ls

Rs

Lt

Rt

+

+

Center

Level

+

+

LFE

Level

+

+

Figure 3.23   

Audio Processing group – Status tab

 

Summary of Contents for DENSITE XVP-1801


































































Reviews:

No comments