background image

 minnkotamotors.com  |  5  

©2018 Johnson Outdoors Marine Electronics, Inc.

WaRRaNTY

NOTICE: 

Do not return your Minn Kota product to your retailer. Your retailer is not authorized to repair or replace products.

NOTICE: 

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. IN NO EVENT SHALL ANY IMPLIED WARRANTIES INCLUDING 

ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND THE DURATION OF THE RELEVANT EXPRESS 

LIMITED WARRANTY. IN NO EVENT SHALL JOME BE LIABLE FOR PUNITIVE, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. Without limiting the 

foregoing, JOME assumes no responsibility for loss of use of product, loss of time, inconvenience or other damage. 

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the 

above limitations and/or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which 

vary from state to state.

WARRANTY ON MINN KOTA SALTWATER TROLLING MOTORS

Johnson Outdoors Marine Electronics, Inc. (“JOME”) extends the following limited warranty to the original retail purchaser only. Warranty coverage is 
not transferable. 

Minn Kota Limited Two-Year Warranty on the Entire Product

JOME warrants to the original retail purchaser only that the purchaser’s new Minn Kota saltwater trolling motor will be materially free from defects in 

materials and workmanship appearing within two (2) years after the date of purchase. JOME will (at its option) either repair or replace, free of charge, 

any parts found by JOME to be defective during the term of this warranty. Such repair, or replacement shall be the sole and exclusive liability of JOME 

and the sole and exclusive remedy of the purchaser for breach of this warranty.

Exclusions & Limitations

This limited warranty does not apply to products that have been used commercially or for rental purposes. This limited warranty does not cover normal 

wear and tear, blemishes that do not affect the operation of the product, or damage caused by accidents, abuse, alteration, modification, shipping 

damages, negligence of the user or misuse, improper or insufficient care or maintenance.

 DAMAGE CAUSED BY THE USE OF OTHER REPLACEMENT PARTS 

NOT MEETING THE DESIGN SPECIFICATIONS OF THE ORIGINAL PARTS WILL NOT BE COVERED BY THIS LIMITED WARRANTY. The cost of normal maintenance or 

replacement parts which are not in breach of the limited warranty  are the responsibility of the purchaser. Prior to using products, the purchaser shall 

determine the suitability of the products for the intended use and assumes all related risk and liability. Any assistance JOME provides to or procures 

for the purchaser outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver of the terms, limitations or exclusions, 

nor will such assistance extend or revive the warranty. JOME will not reimburse the purchaser for any expenses incurred by the purchaser in repairing, 

correcting or replacing any defective products or parts, except those incurred with JOME’s prior written permission. 

JOME’S AGGREGATE LIABILITY WITH 

RESPECT TO COVERED PRODUCTS IS LIMITED TO AN AMOUNT EQUAL TO THE PURCHASER’S ORIGINAL PURCHASE PRICE PAID FOR SUCH PRODUCT.   

Minn Kota Service Information 

To obtain warranty service in the U.S., the product believed to be defective, and proof of original purchase (including the date of purchase), must be 

presented to a Minn Kota Authorized Service Center or to Minn Kota’s factory service center in Mankato, MN. Any charges incurred for service calls, 

transportation or shipping/freight to/from the Minn Kota Authorized Service Center or factory, labor to haul out, remove, re-install or re-rig products 

removed for warranty service, or any other similar items are the sole and exclusive responsibility of the purchaser. Products purchased outside of the 

U.S. must be returned prepaid with proof of purchase (including the date of purchase and serial number) to any Authorized Minn Kota Service Center in 

the country of purchase. Warranty service can be arranged by contacting a Minn Kota Authorized Service Center or by contacting the factory at 1-800-

227-6433 or email [email protected]

Products repaired or replaced will be warranted for the remainder of the original warranty period [or 

for 90 days from the date of repair or replacement, whichever is longer]. For any product that is returned for warranty service that JOME finds to be not 

covered by or not in breach of this limited warranty, there will be a billing for services rendered at the prevailing posted labor rate and for a minimum of at 

least one hour.

Summary of Contents for ENDURA MAX Engine Mount 160





































Reviews: