MIMAKI 3042 MkII EX, Operation Manual

Page: 9 / 126

viii
For safe operation
1
2
2
2
2
2
Never do the following
• Use of the machine under an abnormal
condition where it produces smoke or strange
smell can result in fire or electric shocks. If
such an abnormality is found, be sure to turn
off the power switch immediately and unplug
the cable from the wall outlet. Check first that
the machine no longer produces smoke, and
then contact your distributor or a sales office of
MIMAKI for repair. Never repair your machine
by yourself since it is very dangerous for you
to do so.
• Never disassemble or remodel the main unit of
the machine or the ink cartridge. Disassembly
or remodeling can result in an electric shock or
breakdown of the machine.
• Take care that no dust or dirt sticks to Media
Transfer Surface heaters. Dust and dirt
sticking heaters can cause fire.
• Do not use extension cords. Doing so may
result in fire or electric shocks.
• Keep the power plug prong clear of any
foreign object such as a piece of metal. Failure
to do so may result in a fire or electric shocks.
• Do not plug too may leads into a single socket.
Doing so may result in fire or electric shocks.
• Do not use the machine if the power cord or
plug is damaged. Using the machine with
damaged power cord may result in fire or
electric shocks. Contact your service
representative for replacement cord.
• Do not handle the power plug with wet
hands.Doing so may result in electric shocks.
• Grasp by holding the plug itself when
removing the power plug from wall outlet, and
never hold by the cord. Holding and pulling the
cord may damage the cord, leading to fire or
electric shocks.
• To prevent a fire or electric shock, do not use
the device at a power supply voltage other
than the one indicated.
• To prevent a fire or electric shock, do not use
the device at a power supply frequency other
than the one indicated.
• Keep your fingers and other body parts away
from dangerous moving parts of the device.
• If metals, water, liquids or similar foreign
material enters the device, turn the power
supply off immediately, make sure to
disconnect the power plug, and contact the
service center. Using the device without
addressing the issue can result in a fire or
electric shock.
• In case of ink leakage, please turn off the main
power, unplug the power cable and contact
your local distributor, our sales office, or
service center.
• Keep children away from this machine.
WARNING
WARNING
Do not disassemble or remodel the machine
• Never disassemble or remodel this machine
and the ink bottle.
Disassembling or remodeling any of them will
result in electric shocks or breakdown of this
machine.
Power supply and voltage
• Use this machine with indicated power
specifications.
Be sure to connect the power cable plug to the
grounded outlet, or it may cause fire or electric
shock.
• Never look at the LED UV being lit with your
naked eyes, or it may cause pain in your eyes
or visual impairment. Be sure to wear safety
glasses.
• Do not apply ultraviolet (UV) light directly to
your skin, or it may cause irritation on your
skin.
• To prevent electrical shock, be sure to set OFF
the main power circuit breaker and disconnect
the power plug before carrying out
maintenance. For some units, capacitors may
take one minute for discharging; therefore,
start maintenance work three minutes after
setting OFF the main power circuit breaker
and disconnecting the power plug.
• If LED UV has been damaged, you should
replace the LED UV that has reached or has
past its rating life.
• The main power circuit breaker should be set
ON only by personnel with sufficient
knowledge about operations of this machine.
• Do not touch the lamp with bare hands while
lighting or right after the lamp off to avoid from
burn injury.
• Although this machine is a Class 1 laser
device, its laser sensors are equipped with
Class 2 lasers. Never look directly at the laser
light, as it can make your eyes hurt or damage
your eyesight.
Do not use this machine in damp places
• Avoid damp environment to use this machine.
Do not splash water onto this machine. High
humidity or water will give rise to fire, electric
shocks or breakdown of this machine.