24
25
effi ciency of the machine depends on the size and quality of
the fi lter and dust bag. Therefore - use only Original fi lter
and dust bags.
AFTER USING THE MACHINE
After use
Remove the plug from the socket when machine is not in
use. Wind up the cord starting from the machine. The power
cord can be wound up around the motor top or at the
container or placed in the included hook, or fastening
means. Some variants have special storage places for
accessories.
Transport
• Before transporting the machine, close all the latches.
• Do not tilt the machine if there are liquids in the dirt tank.
• Do not use a crane hook to lift the machine.
• Do not lift the machine by the trolley handle
•
Storage
CAUTION
!
Store the appliance in a dry place, protected from rain and
frost. The machine shall be stored indoors only.
Accessory and tool storage
For convenient transport and storage of accessories or
tools, integrated rails are found on side of machine which
allows fastening with straps or other means. A fl exible strap
and hooks are included on back of machine for attachment
of suction hose or mains cable. For instruction see quick
reference guide.
An optional adapter plate with attachment system can be
installed on top of machine for fastening of 2-point or 4-point
storage cases.
Remove the electrical plug from the socket before installing
the adapter plate.
CAUTION
!
Do not lift machine in adapter plate without having storage
case safely installed. Note the weight and balance of the
appliance in case of storage. Maximum weight of storage
cases is 30 kg.
Recycling the machine
Make the old machine unusable.
1. Unplug the machine.
2. Cut the power cord.
3. Do not discard of electrical appliances with household
waste.
As specifi ed in European Directive 2012/19/EU on
old electrical and electronic appliances, used
electrical goods must be collected separately and
recycled ecologically.
MAINTENANCE
Regular servicing and inspection
Regular servicing and inspection of your machine must be
carried out by suitably qualifi ed personnel in accordance
with relevant legislation and regulations. In particular,
electrical tests for earth continuity, insulation resistance, and
condition of the fl exible cord should be checked frequently.
In the event of any defect, the machine MUST be withdrawn
from service, completely checked and repaired by an
authorized service technician.
At least once a year, a Milwaukee technician or an
instructed person must perform a technical inspection
including fi lters, air tightness and control mechanisms.
Maintenance
Remove the plug from the socket before performing
maintenance. Before using the machine make sure that the
frequency and voltage shown on the rating plate correspond
with the mains voltage.
The machine is designed for continuous heavy work.
Depending on the number of running hours – the dust fi lter
should be renewed. Keep the machine clean with a dry
cloth, and a small amount of spray polish.
During maintenance and cleaning, handle the machine in
such a manner that there is no danger for maintenance staff
or other persons.
In the maintenance area
• Use fi ltered compulsory ventilation
• Wear protective clothing
• Clean the maintenance area so that no harmful
substances get into the surroundings.
During maintenance and repair work all contaminated parts
that could not be cleaned satisfactorily must be:
• Packed in well sealed bags
• Disposed of in a manner that complies with valid
regulations for such waste removal.
CAUTION Clean the water level limiting device regularly and
examine it for signs of damage.
Use only Milwaukee accessories and Milwaukee spare
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
EU DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under “Technical Data” fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC and the following standards have been
used:
EN 60335-1:2012+A11:2014
EN 60335-2-69:2012
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012
Winnenden, 2017-02-06
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
ENGLISH
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before
starting the machine.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Dust Class L
(IEC 60335-2-69).
The dusts which belong to
this class have OEL
1)
values > 1mg/m3.
European Conformity Mark
ENGLISH
